Project

General

Profile

Bug #2459

Updated by tuxillo over 10 years ago

With the x86_64 snapshot from Oct 30 2012, I am unable to use the NIC or USB 
 
 storage drives on a probook 4510s.    I have the same trouble with 3.2.1. 

 

 If attempting to use the NIC, I get a number of these messages: 

 

 msk0: watchdog timeout (missed Tx interrupts) -- recovering 

 

 If I plug in a USB drive, it is simply unrecognized.    It also appears as if 
 
 the port I have plugged it into shuts itself down...    I have these drives 
 
 that have a light on them when plugged in to a USB; when I plug them in using 3.3 
 
 they have the light for about half a second and then shut off. 

 

 If I boot with "hw.ioapic_enable=0" I am able to use both the NIC and USB drives. 

 

 Here is a verbose dmesg: 

 

 Copyright (c) 2003-2012 The DragonFly Project. 
 
 Copyright (c) 1992-2003 The FreeBSD Project. 
 
 Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 
	 
	 The Regents of the University of California. All rights reserved. 
 
 Slab ZoneSize set to 128KB 
 
 Leaving critical section, allowing interrupts 
 
 ACPI SDT: RSDP not in EBDA 
 
 ACPI SDT: RSDP in BIOS mem 
 
 ACPI FADT: SCI irq 9, conform/conform 
 
 DragonFly v3.3.0.506.gaad8a0-DEVELOPMENT #0: Tue Oct 30 19:01:13 UTC 2012 
     
     root@pkgbox64.dragonflybsd.org:/usr/obj/usr/src/sys/X86_64_GENERIC 
 
 Calibrating clock(s) ... TSC clock: 2094746661 Hz, i8254 clock: 1193180 Hz 
 
 CLK_USE_I8254_CALIBRATION not specified - using default frequency 
 
 CLK_USE_TSC_CALIBRATION not specified - using old calibration method 
 
 CPU: Intel(R) Core(TM)2 Duo CPU       T6570    @ 2.10GHz (2094.77-MHz K8-class CPU) 
   
   Origin = "GenuineIntel"    Id = 0x1067a    Stepping = 10 
   
   Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> 
   
   Features2=0x408e3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,XSAVE> 
   
   AMD Features=0x20100800<SYSCALL,NX,LM> 
   
   AMD Features2=0x1<LAHF> 
 
 real memory    = 2072271872 (1976 MB) 
 
 Physical memory chunk(s): 
 
 0x00020000 - 0x0007ffff, 393216 bytes (96 pages) 
 
 0x00100000 - 0x001fffff, 1048576 bytes (256 pages) 
 
 0x035a0000 - 0x76b3ffff, 1935278080 bytes (472480 pages) 
 
 0x76b60000 - 0x7795ffff, 14680064 bytes (3584 pages) 
 
 0x77980000 - 0x7a0fffff, 41418752 bytes (10112 pages) 
 
 0x7a320000 - 0x7ba5ffff, 24379392 bytes (5952 pages) 
 
 avail memory = 1894744064 (1806 MB) 
 
 ACPI MADT: LAPIC address 0xfee00000, flags 0x1 
 
 ACPI MADT: BSP apic id 0 
 
 ACPI MADT: cpu id 0, apic id 0 
 
 ACPI MADT: cpu id 1, apic id 1 
 
 lapic: divisor index 0, frequency 99750420 Hz 
 
 SMP: CPU0 apic_initialize(): 
      
      lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff 
 
 SMP: Waiting APs LAPIC initialization 
 
 SMP: CPU1 apic_initialize(): 
      
      lint0: 0x00010000 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff 
 
 ACPI MADT: warning invalid intsrc irq 9 trig, level 
 
 ACPI MADT: IOAPIC addr 0xfec00000, apic id 1, gsi base 0 
 
 ACPI MADT: INTSRC irq 0 -> gsi 2 edge/high 
 
 ACPI MADT: SCI irq 9, first test level/high 
 
 IOAPIC: idx 0, apic id 2, gsi base 0, npin 24 
 
 IOAPIC: irq 1, gsi 1 -> cpu0 (fixed) 
 
 IOAPIC: irq 1 -> gsi 1 edge/high 
 
 IOAPIC: irq 0, gsi 2 -> cpu0 (0) 
 
 IOAPIC: irq 0 -> gsi 2 edge/high 
 
 IOAPIC: irq 3, gsi 3 -> cpu0 (fixed) 
 
 IOAPIC: irq 3 -> gsi 3 edge/high 
 
 IOAPIC: irq 4, gsi 4 -> cpu0 (fixed) 
 
 IOAPIC: irq 4 -> gsi 4 edge/high 
 
 IOAPIC: irq 5, gsi 5 -> cpu0 (fixed) 
 
 IOAPIC: irq 5 -> gsi 5 edge/high 
 
 IOAPIC: irq 6, gsi 6 -> cpu0 (fixed) 
 
 IOAPIC: irq 6 -> gsi 6 edge/high 
 
 IOAPIC: irq 7, gsi 7 -> cpu0 (fixed) 
 
 IOAPIC: irq 7 -> gsi 7 edge/high 
 
 IOAPIC: irq 8, gsi 8 -> cpu0 (fixed) 
 
 IOAPIC: irq 8 -> gsi 8 edge/high 
 
 IOAPIC: irq 9, gsi 9 -> cpu0 (sci) 
 
 IOAPIC: irq 9 -> gsi 9 edge/high 
 
 IOAPIC: irq 10, gsi 10 -> cpu0 (fixed) 
 
 IOAPIC: irq 10 -> gsi 10 edge/high 
 
 IOAPIC: irq 11, gsi 11 -> cpu0 (fixed) 
 
 IOAPIC: irq 11 -> gsi 11 edge/high 
 
 IOAPIC: irq 12, gsi 12 -> cpu0 (fixed) 
 
 IOAPIC: irq 12 -> gsi 12 edge/high 
 
 IOAPIC: irq 13, gsi 13 -> cpu0 (fixed) 
 
 IOAPIC: irq 13 -> gsi 13 edge/high 
 
 IOAPIC: irq 14, gsi 14 -> cpu0 (fixed) 
 
 IOAPIC: irq 14 -> gsi 14 edge/high 
 
 IOAPIC: irq 15, gsi 15 -> cpu0 (fixed) 
 
 IOAPIC: irq 15 -> gsi 15 edge/high 
 
 IOAPIC: irq 16, gsi 16 -> cpu0 (fixed) 
 
 IOAPIC: irq 16 -> gsi 16 level/low 
 
 IOAPIC: irq 17, gsi 17 -> cpu0 (fixed) 
 
 IOAPIC: irq 17 -> gsi 17 level/low 
 
 IOAPIC: irq 18, gsi 18 -> cpu0 (fixed) 
 
 IOAPIC: irq 18 -> gsi 18 level/low 
 
 IOAPIC: irq 19, gsi 19 -> cpu0 (fixed) 
 
 IOAPIC: irq 19 -> gsi 19 level/low 
 
 IOAPIC: irq 20, gsi 20 -> cpu0 (fixed) 
 
 IOAPIC: irq 20 -> gsi 20 level/low 
 
 IOAPIC: irq 21, gsi 21 -> cpu0 (fixed) 
 
 IOAPIC: irq 21 -> gsi 21 level/low 
 
 IOAPIC: irq 22, gsi 22 -> cpu0 (fixed) 
 
 IOAPIC: irq 22 -> gsi 22 level/low 
 
 IOAPIC: irq 23, gsi 23 -> cpu0 (fixed) 
 
 IOAPIC: irq 23 -> gsi 23 level/low 
 
 IOAPIC: cpu0 irq 2 reserved 
 
 IOAPIC: cpu1 irq 0 reserved 
 
 IOAPIC: cpu1 irq 1 reserved 
 
 IOAPIC: cpu1 irq 2 reserved 
 
 IOAPIC: cpu1 irq 3 reserved 
 
 IOAPIC: cpu1 irq 4 reserved 
 
 IOAPIC: cpu1 irq 5 reserved 
 
 IOAPIC: cpu1 irq 6 reserved 
 
 IOAPIC: cpu1 irq 7 reserved 
 
 IOAPIC: cpu1 irq 8 reserved 
 
 IOAPIC: cpu1 irq 9 reserved 
 
 IOAPIC: cpu1 irq 10 reserved 
 
 IOAPIC: cpu1 irq 11 reserved 
 
 IOAPIC: cpu1 irq 12 reserved 
 
 IOAPIC: cpu1 irq 13 reserved 
 
 IOAPIC: cpu1 irq 14 reserved 
 
 IOAPIC: cpu1 irq 15 reserved 
 
 IOAPIC: legacy irq max 24 
 
 ELCR Found.    ISA IRQs programmed as: 
   
   0    1    2    3    4    5    6    7    8    9 10 11 12 13 14 15 
   
   E    E    E    E    E    E    E    E    E    E    L    L    E    E    E    E 
 
 Initialize MI interrupts 
 
 objcache: magazine cap [6, 134] 
 
 Finish MP startup 
 
 Active CPU Mask: 0000000000000003 
 
 ndepotmags=263 x mag_cap=134 for mbuf 
 
 ndepotmags=132 x mag_cap=134 for mbuf pkt hdr 
 
 ndepotmags=17    x mag_cap=134 for cluster mbuf 
 
 ndepotmags=8     x mag_cap=134 for jcluster mbuf 
 
 ndepotmags=9     x mag_cap=134 for mbuf + cluster 
 
 ndepotmags=6     x mag_cap=46    for mbuf pkt hdr + cluster 
 
 ndepotmags=6     x mag_cap=46    for mbuf + jcluster 
 
 ndepotmags=6     x mag_cap=22    for mbuf pkt hdr + jcluster 
 
 ndepotmags=6     x mag_cap=22    for sf_buf 
 
 ndepotmags=2     x mag_cap=6     for exec-args 
 
 Preloaded elf kernel "kernel" at 0xffffffff83008000. 
 
 Preloaded elf obj module "acpi.ko" at 0xffffffff83008550. 
 
 Preloaded elf obj module "ehci.ko" at 0xffffffff83008ee8. 
 
 link_elf_obj_obj: symbol atomic_swap_int undefined 
 
 KLD file acpi.ko - could not finalize loading 
 
 BITS within APICID: logical_CPU_bits: 0; core_bits: 1 
 
 CPU Topology: cores_per_chip: 2; threads_per_core: 1; chips_per_package: 1; 
 
 Start scheduler helpers on cpus: 
	 
	 cpu0 - No HT available, multi-core/physical cpu. Physical siblings: cpu0 cpu1  
	  
	 cpu1 - No HT available, multi-core/physical cpu. Physical siblings: cpu0 cpu1  
  
 Start scheduler helpers on cpus: 
	 
	 cpu0 - No HT available, multi-core/physical cpu. Physical siblings: cpu0 cpu1  
	  
	 cpu1 - No HT available, multi-core/physical cpu. Physical siblings: cpu0 cpu1  
  
 start dummy scheduler helpers on cpus: 0 1 
 
 ndepotmags=6     x mag_cap=6     for thread 
 
 ndepotmags=6     x mag_cap=22    for dsched-tdio-cache 
 
 ndepotmags=6     x mag_cap=22    for dsched-tdctx-cache 
 
 ndepotmags=6     x mag_cap=22    for dsched-diskctx-cache 
 
 ndepotmags=6     x mag_cap=6     for vmspace 
 
 ndepotmags=6     x mag_cap=22    for devfs-node-cache 
 
 ndepotmags=6     x mag_cap=22    for devfs-msg-cache 
 
 ndepotmags=6     x mag_cap=22    for devfs-dev-cache 
 
 ndepotmags=6     x mag_cap=22    for disk-msg-cache 
 
 FQ scheduler policy version 1.1 loaded 
 
 ndepotmags=6     x mag_cap=22    for pdict128 
 
 ndepotmags=6     x mag_cap=6     for devfs 
 
 wdog: In-kernel automatic watchdog reset enabled 
 
 ndepotmags=6     x mag_cap=22    for pdict32 
 
 ndepotmags=6     x mag_cap=22    for propdata 
 
 ndepotmags=6     x mag_cap=22    for pdict16 
 
 ndepotmags=6     x mag_cap=22    for propnmbr 
 
 ndepotmags=6     x mag_cap=22    for proparay 
 
 ndepotmags=6     x mag_cap=22    for propdict 
 
 ndepotmags=6     x mag_cap=22    for propstng 
 
 ndepotmags=6     x mag_cap=22    for devfs-rule-cache 
 
 wlan: <802.11 Link Layer> 
 
 ndepotmags=6     x mag_cap=22    for ata_request 
 
 ndepotmags=6     x mag_cap=22    for ata_composite 
 
 No policy for md0 specified, or policy not found 
 
 disk scheduler: set policy of md0 to noop 
 
 md0: Malloc disk 
 
 kbd: new array size 4 
 
 kbd1 at kbdmux0 
 
 ndepotmags=6     x mag_cap=22    for crypto op 
 
 ndepotmags=6     x mag_cap=22    for crypto desc 
 
 crypto: <crypto core> 
 
 md0: invalid primary partition table: no magic 
 
 hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2 
 
 hpt27xx: RocketRAID 27xx controller driver v1.0 (Oct 30 2012 19:00:45) 
 
 IOAPIC: rman cpu0 0 - 1 
 
 IOAPIC: rman cpu0 3 - 95 
 
 IOAPIC: rman cpu0 97 - 191 
 
 IOAPIC: rman cpu1 16 - 95 
 
 IOAPIC: rman cpu1 97 - 191 
 
 cryptosoft0.nexus0.root0 
 
 cryptosoft0: <software crypto> [tentative] on motherboard 
 
 crypto: assign cryptosoft0 driver id 0, flags 234881024 
 
 crypto: cryptosoft0 registers alg 1 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 2 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 3 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 4 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 5 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 16 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 6 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 7 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 18 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 19 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 20 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 8 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 15 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 9 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 10 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 13 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 14 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 11 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 22 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 23 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 24 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 28 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 25 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 26 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 27 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 21 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 29 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 30 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 31 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 32 flags 0 maxoplen 0 
 
 crypto: cryptosoft0 registers alg 17 flags 0 maxoplen 0 
 
 cryptosoft0: <software crypto> [attached!] on motherboard 
 
 pcib0.legacy0.nexus0.root0 
 
 pcib0: <MPTABLE Host-PCI bridge> [tentative] pcibus 0 on motherboard 
 
 pci0.pcib0.legacy0.nexus0.root0 
 
 pci0: <PCI bus> [tentative] on pcib0 
 
 pci0: domain=0, physical bus=0 
 
 found-> 	 vendor=0x8086, dev=0x2a40, revid=0x07 
	 
	 domain=0, bus=0, slot=0, func=0 
	 
	 class=06-00-00, hdrtype=0x00, mfdev=0 
	 
	 cmdreg=0x0006, statreg=0x2090, cachelnsz=0 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) 
 
 found-> 	 vendor=0x8086, dev=0x2a42, revid=0x07 
	 
	 domain=0, bus=0, slot=2, func=0 
	 
	 class=03-00-00, hdrtype=0x00, mfdev=1 
	 
	 cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) 
	 
	 intpin=a, irq=10 
	 
	 powerspec 3    supports D0 D3    current D0 
	 
	 MSI supports 1 message 
	 
	 map[10]: type Memory, range 64, base 0x90000000, size 22, enabled 
	 
	 map[18]: type Prefetchable Memory, range 64, base 0x80000000, size 28, enabled 
	 
	 map[20]: type I/O Port, range 32, base 0x70f0, size    3, enabled 
 
 MPTABLE: fixed interrupt routing for 0:2 INTA 
 
 MPTABLE: 0:2 INTA routed to irq 10 
 
 IOAPIC: irq 10, gsi 10 edge/high -> level/low 
 
 found-> 	 vendor=0x8086, dev=0x2a43, revid=0x07 
	 
	 domain=0, bus=0, slot=2, func=1 
	 
	 class=03-80-00, hdrtype=0x00, mfdev=1 
	 
	 cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) 
	 
	 powerspec 3    supports D0 D3    current D0 
	 
	 map[10]: type Memory, range 64, base 0x90400000, size 20, enabled 
 
 found-> 	 vendor=0x8086, dev=0x2937, revid=0x03 
	 
	 domain=0, bus=0, slot=26, func=0 
	 
	 class=0c-03-00, hdrtype=0x00, mfdev=1 
	 
	 cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) 
	 
	 intpin=a, irq=10 
	 
	 map[20]: type I/O Port, range 32, base 0x70c0, size    5, enabled 
 
 MPTABLE: fixed interrupt routing for 0:26 INTA 
 
 MPTABLE: 0:26 INTA routed to irq 10 
 
 found-> 	 vendor=0x8086, dev=0x2938, revid=0x03 
	 
	 domain=0, bus=0, slot=26, func=1 
	 
	 class=0c-03-00, hdrtype=0x00, mfdev=0 
	 
	 cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) 
	 
	 intpin=b, irq=11 
	 
	 map[20]: type I/O Port, range 32, base 0x70a0, size    5, enabled 
 
 MPTABLE: fixed interrupt routing for 0:26 INTB 
 
 MPTABLE: 0:26 INTB routed to irq 11 
 
 IOAPIC: irq 11, gsi 11 edge/high -> level/low 
 
 found-> 	 vendor=0x8086, dev=0x2939, revid=0x03 
	 
	 domain=0, bus=0, slot=26, func=2 
	 
	 class=0c-03-00, hdrtype=0x00, mfdev=0 
	 
	 cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) 
	 
	 intpin=c, irq=10 
	 
	 map[20]: type I/O Port, range 32, base 0x7080, size    5, enabled 
 
 MPTABLE: fixed interrupt routing for 0:26 INTC 
 
 MPTABLE: 0:26 INTC routed to irq 10 
 
 found-> 	 vendor=0x8086, dev=0x293c, revid=0x03 
	 
	 domain=0, bus=0, slot=26, func=7 
	 
	 class=0c-03-20, hdrtype=0x00, mfdev=0 
	 
	 cmdreg=0x0006, statreg=0x0290, cachelnsz=0 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) 
	 
	 intpin=d, irq=10 
	 
	 powerspec 2    supports D0 D3    current D0 
	 
	 map[10]: type Memory, range 32, base 0x98904c00, size 10, enabled 
 
 MPTABLE: fixed interrupt routing for 0:26 INTD 
 
 MPTABLE: 0:26 INTD routed to irq 10 
 
 found-> 	 vendor=0x8086, dev=0x293e, revid=0x03 
	 
	 domain=0, bus=0, slot=27, func=0 
	 
	 class=04-03-00, hdrtype=0x00, mfdev=0 
	 
	 cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) 
	 
	 intpin=a, irq=11 
	 
	 powerspec 2    supports D0 D3    current D0 
	 
	 MSI supports 1 message, 64 bit 
	 
	 PCI Express ver.1 cap=0x0091[ROOTDEV] 
	 
	 map[10]: type Memory, range 64, base 0x98900000, size 14, enabled 
 
 MPTABLE: fixed interrupt routing for 0:27 INTA 
 
 MPTABLE: 0:27 INTA routed to irq 11 
 
 found-> 	 vendor=0x8086, dev=0x2940, revid=0x03 
	 
	 domain=0, bus=0, slot=28, func=0 
	 
	 class=06-04-00, hdrtype=0x01, mfdev=1 
	 
	 cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) 
	 
	 intpin=a, irq=10 
	 
	 powerspec 2    supports D0 D3    current D0 
	 
	 MSI supports 1 message 
	 
	 PCI Express ver.1 cap=0x0141[ROOT], slotcap=0x0000a0e0[HOTPLUG] 
 
 MPTABLE: fixed interrupt routing for 0:28 INTA 
 
 MPTABLE: 0:28 INTA routed to irq 10 
 
 found-> 	 vendor=0x8086, dev=0x2942, revid=0x03 
	 
	 domain=0, bus=0, slot=28, func=1 
	 
	 class=06-04-00, hdrtype=0x01, mfdev=1 
	 
	 cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) 
	 
	 intpin=b, irq=11 
	 
	 powerspec 2    supports D0 D3    current D0 
	 
	 MSI supports 1 message 
	 
	 PCI Express ver.1 cap=0x0141[ROOT], slotcap=0x0008a0e0[HOTPLUG] 
 
 MPTABLE: fixed interrupt routing for 0:28 INTB 
 
 MPTABLE: 0:28 INTB routed to irq 11 
 
 found-> 	 vendor=0x8086, dev=0x2944, revid=0x03 
	 
	 domain=0, bus=0, slot=28, func=2 
	 
	 class=06-04-00, hdrtype=0x01, mfdev=1 
	 
	 cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) 
	 
	 intpin=c, irq=10 
	 
	 powerspec 2    supports D0 D3    current D0 
	 
	 MSI supports 1 message 
	 
	 PCI Express ver.1 cap=0x0141[ROOT], slotcap=0x0010a0e0[HOTPLUG] 
 
 MPTABLE: fixed interrupt routing for 0:28 INTC 
 
 MPTABLE: 0:28 INTC routed to irq 10 
 
 found-> 	 vendor=0x8086, dev=0x2948, revid=0x03 
	 
	 domain=0, bus=0, slot=28, func=4 
	 
	 class=06-04-00, hdrtype=0x01, mfdev=1 
	 
	 cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) 
	 
	 intpin=a, irq=10 
	 
	 powerspec 2    supports D0 D3    current D0 
	 
	 MSI supports 1 message 
	 
	 PCI Express ver.1 cap=0x0141[ROOT], slotcap=0x0020a0e0[HOTPLUG] 
 
 MPTABLE: fixed interrupt routing for 0:28 INTA 
 
 MPTABLE: 0:28 INTA routed to irq 10 
 
 found-> 	 vendor=0x8086, dev=0x294a, revid=0x03 
	 
	 domain=0, bus=0, slot=28, func=5 
	 
	 class=06-04-00, hdrtype=0x01, mfdev=1 
	 
	 cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) 
	 
	 intpin=b, irq=11 
	 
	 powerspec 2    supports D0 D3    current D0 
	 
	 MSI supports 1 message 
	 
	 PCI Express ver.1 cap=0x0141[ROOT], slotcap=0x0028a0e0[HOTPLUG] 
 
 MPTABLE: fixed interrupt routing for 0:28 INTB 
 
 MPTABLE: 0:28 INTB routed to irq 11 
 
 found-> 	 vendor=0x8086, dev=0x2934, revid=0x03 
	 
	 domain=0, bus=0, slot=29, func=0 
	 
	 class=0c-03-00, hdrtype=0x00, mfdev=1 
	 
	 cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) 
	 
	 intpin=a, irq=10 
	 
	 map[20]: type I/O Port, range 32, base 0x7060, size    5, enabled 
 
 MPTABLE: fixed interrupt routing for 0:29 INTA 
 
 MPTABLE: 0:29 INTA routed to irq 10 
 
 found-> 	 vendor=0x8086, dev=0x2935, revid=0x03 
	 
	 domain=0, bus=0, slot=29, func=1 
	 
	 class=0c-03-00, hdrtype=0x00, mfdev=0 
	 
	 cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) 
	 
	 intpin=b, irq=10 
	 
	 map[20]: type I/O Port, range 32, base 0x7040, size    5, enabled 
 
 MPTABLE: fixed interrupt routing for 0:29 INTB 
 
 MPTABLE: 0:29 INTB routed to irq 10 
 
 found-> 	 vendor=0x8086, dev=0x2936, revid=0x03 
	 
	 domain=0, bus=0, slot=29, func=2 
	 
	 class=0c-03-00, hdrtype=0x00, mfdev=0 
	 
	 cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) 
	 
	 intpin=c, irq=10 
	 
	 map[20]: type I/O Port, range 32, base 0x7020, size    5, enabled 
 
 MPTABLE: fixed interrupt routing for 0:29 INTC 
 
 MPTABLE: 0:29 INTC routed to irq 10 
 
 found-> 	 vendor=0x8086, dev=0x293a, revid=0x03 
	 
	 domain=0, bus=0, slot=29, func=7 
	 
	 class=0c-03-20, hdrtype=0x00, mfdev=0 
	 
	 cmdreg=0x0006, statreg=0x0290, cachelnsz=0 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) 
	 
	 intpin=d, irq=10 
	 
	 powerspec 2    supports D0 D3    current D0 
	 
	 map[10]: type Memory, range 32, base 0x98904800, size 10, enabled 
 
 MPTABLE: fixed interrupt routing for 0:29 INTD 
 
 MPTABLE: 0:29 INTD routed to irq 10 
 
 found-> 	 vendor=0x8086, dev=0x2448, revid=0x93 
	 
	 domain=0, bus=0, slot=30, func=0 
	 
	 class=06-04-01, hdrtype=0x01, mfdev=0 
	 
	 cmdreg=0x0107, statreg=0x0010, cachelnsz=0 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns) 
 
 found-> 	 vendor=0x8086, dev=0x2919, revid=0x03 
	 
	 domain=0, bus=0, slot=31, func=0 
	 
	 class=06-01-00, hdrtype=0x00, mfdev=1 
	 
	 cmdreg=0x0007, statreg=0x0210, cachelnsz=0 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) 
 
 found-> 	 vendor=0x8086, dev=0x2929, revid=0x03 
	 
	 domain=0, bus=0, slot=31, func=2 
	 
	 class=01-06-01, hdrtype=0x00, mfdev=0 
	 
	 cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) 
	 
	 intpin=a, irq=10 
	 
	 powerspec 3    supports D0 D3    current D0 
	 
	 MSI supports 16 messages 
	 
	 map[10]: type I/O Port, range 32, base 0x70e8, size    3, enabled 
	 
	 map[14]: type I/O Port, range 32, base 0x70fc, size    2, enabled 
	 
	 map[18]: type I/O Port, range 32, base 0x70e0, size    3, enabled 
	 
	 map[1c]: type I/O Port, range 32, base 0x70f8, size    2, enabled 
	 
	 map[20]: type I/O Port, range 32, base 0x7000, size    5, enabled 
	 
	 map[24]: type Memory, range 32, base 0x98904000, size 11, enabled 
 
 MPTABLE: fixed interrupt routing for 0:31 INTA 
 
 MPTABLE: 0:31 INTA routed to irq 10 
 
 vgapci0.pci0.pcib0.legacy0.nexus0.root0 
 
 vgapci0: <VGA-compatible display> [tentative] port 0x70f0-0x70f7 mem 0x80000000-0x8fffffff,0x90000000-0x903fffff irq 10 at device 2.0 on pci0 
 
 agp0.vgapci0.pci0.pcib0.legacy0.nexus0.root0 
 
 agp0: <Intel GM45 SVGA controller> [tentative] on vgapci0 
 
 vgapci0: Reserved 0x10000000 bytes for rid 0x18 type 3 at 0x80000000 
 
 vgapci0: Reserved 0x400000 bytes for rid 0x10 type 3 at 0x90000000 
 
 agp0: detected 65532k stolen memory 
 
 agp0: aperture size is 256M 
 
 agp0: <Intel GM45 SVGA controller> [attached!] on vgapci0 
 
 vgapci0: <VGA-compatible display> [attached!] port 0x70f0-0x70f7 mem 0x80000000-0x8fffffff,0x90000000-0x903fffff irq 10 at device 2.0 on pci0 
 
 vgapci1.pci0.pcib0.legacy0.nexus0.root0 
 
 vgapci1: <VGA-compatible display> [tentative] mem 0x90400000-0x904fffff at device 2.1 on pci0 
 
 vgapci1: <VGA-compatible display> [attached!] mem 0x90400000-0x904fffff at device 2.1 on pci0 
 
 uhci0.pci0.pcib0.legacy0.nexus0.root0 
 
 uhci0: <Intel 82801I (ICH9) USB controller> [tentative] port 0x70c0-0x70df irq 10 at device 26.0 on pci0 
 
 uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x70c0 
 
 usb0.uhci0.pci0.pcib0.legacy0.nexus0.root0 
 
 usb0: <Intel 82801I (ICH9) USB controller> [tentative] on uhci0 
 
 usb0: USB revision 1.0 
 
 uhub0.usb0.uhci0.pci0.pcib0.legacy0.nexus0.root0 
 
 uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [tentative] on usb0 
 
 uhub0: 2 ports with 2 removable, self powered 
 
 uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [attached!] on usb0 
 
 usb0: <Intel 82801I (ICH9) USB controller> [attached!] on uhci0 
 
 uhci0: <Intel 82801I (ICH9) USB controller> [attached!] port 0x70c0-0x70df irq 10 at device 26.0 on pci0 
 
 uhci1.pci0.pcib0.legacy0.nexus0.root0 
 
 uhci1: <Intel 82801I (ICH9) USB controller> [tentative] port 0x70a0-0x70bf irq 11 at device 26.1 on pci0 
 
 uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0x70a0 
 
 usb1.uhci1.pci0.pcib0.legacy0.nexus0.root0 
 
 usb1: <Intel 82801I (ICH9) USB controller> [tentative] on uhci1 
 
 usb1: USB revision 1.0 
 
 uhub1.usb1.uhci1.pci0.pcib0.legacy0.nexus0.root0 
 
 uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [tentative] on usb1 
 
 uhub1: 2 ports with 2 removable, self powered 
 
 uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [attached!] on usb1 
 
 usb1: <Intel 82801I (ICH9) USB controller> [attached!] on uhci1 
 
 uhci1: <Intel 82801I (ICH9) USB controller> [attached!] port 0x70a0-0x70bf irq 11 at device 26.1 on pci0 
 
 uhci2.pci0.pcib0.legacy0.nexus0.root0 
 
 uhci2: <Intel 82801I (ICH9) USB controller> [tentative] port 0x7080-0x709f irq 10 at device 26.2 on pci0 
 
 uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0x7080 
 
 usb2.uhci2.pci0.pcib0.legacy0.nexus0.root0 
 
 usb2: <Intel 82801I (ICH9) USB controller> [tentative] on uhci2 
 
 usb2: USB revision 1.0 
 
 uhub2.usb2.uhci2.pci0.pcib0.legacy0.nexus0.root0 
 
 uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [tentative] on usb2 
 
 uhub2: 2 ports with 2 removable, self powered 
 
 uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [attached!] on usb2 
 
 usb2: <Intel 82801I (ICH9) USB controller> [attached!] on uhci2 
 
 uhci2: <Intel 82801I (ICH9) USB controller> [attached!] port 0x7080-0x709f irq 10 at device 26.2 on pci0 
 
 ehci0.pci0.pcib0.legacy0.nexus0.root0 
 
 ehci0: <EHCI (generic) USB 2.0 controller> [tentative] mem 0x98904c00-0x98904fff irq 10 at device 26.7 on pci0 
 
 ehci0: Reserved 0x400 bytes for rid 0x10 type 3 at 0x98904c00 
 
 usb3: EHCI version 1.0 
 
 usb3: companion controllers, 2 ports each: usb0 usb1 usb2 
 
 usb3.ehci0.pci0.pcib0.legacy0.nexus0.root0 
 
 usb3: <EHCI (generic) USB 2.0 controller> [tentative] on ehci0 
 
 usb3: USB revision 2.0 
 
 uhub3.usb3.ehci0.pci0.pcib0.legacy0.nexus0.root0 
 
 uhub3: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> [tentative] on usb3 
 
 uhub3: 6 ports with 6 removable, self powered 
 
 uhub3: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> [attached!] on usb3 
 
 usb3: <EHCI (generic) USB 2.0 controller> [attached!] on ehci0 
 
 ehci0: <EHCI (generic) USB 2.0 controller> [attached!] mem 0x98904c00-0x98904fff irq 10 at device 26.7 on pci0 
 
 pci0: <multimedia, HDA> (vendor 0x8086, dev 0x293e) at device 27.0 irq 11 
 
 pcib1.pci0.pcib0.legacy0.nexus0.root0 
 
 pcib1: <MPTABLE PCI-PCI bridge> [tentative] irq 10 at device 28.0 on pci0 
 
 pcib1:     domain              0 
 
 pcib1:     secondary bus       1 
 
 pcib1:     subordinate bus     1 
 
 pcib1:     I/O decode          0xf000-0xfff 
 
 pcib1:     memory decode       0x98800000-0x988fffff 
 
 pcib1:     no prefetched decode 
 
 pcib1: Disable PCI Express hot-plug interrupts(0x0009) 
 
 pci1.pcib1.pci0.pcib0.legacy0.nexus0.root0 
 
 pci1: <PCI bus> [tentative] on pcib1 
 
 pci1: domain=0, physical bus=1 
 
 pci1: <PCI bus> [attached!] on pcib1 
 
 pcib1: <MPTABLE PCI-PCI bridge> [attached!] irq 10 at device 28.0 on pci0 
 
 pcib2.pci0.pcib0.legacy0.nexus0.root0 
 
 pcib2: <MPTABLE PCI-PCI bridge> [tentative] irq 11 at device 28.1 on pci0 
 
 pcib2:     domain              0 
 
 pcib2:     secondary bus       2 
 
 pcib2:     subordinate bus     2 
 
 pcib2:     I/O decode          0xf000-0xfff 
 
 pcib2:     memory decode       0x98700000-0x987fffff 
 
 pcib2:     no prefetched decode 
 
 pci2.pcib2.pci0.pcib0.legacy0.nexus0.root0 
 
 pci2: <PCI bus> [tentative] on pcib2 
 
 pci2: domain=0, physical bus=2 
 
 found-> 	 vendor=0x8086, dev=0x4237, revid=0x00 
	 
	 domain=0, bus=2, slot=0, func=0 
	 
	 class=02-80-00, hdrtype=0x00, mfdev=0 
	 
	 cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) 
	 
	 intpin=a, irq=11 
	 
	 powerspec 3    supports D0 D3    current D0 
	 
	 MSI supports 1 message, 64 bit 
	 
	 PCI Express ver.1 cap=0x0001[DEVICE] 
	 
	 map[10]: type Memory, range 64, base 0x98700000, size 13, enabled 
 
 pcib2: requested memory range 0x98700000-0x98701fff: good 
 
 MPTABLE: fixed interrupt routing for 0:28 INTA 
 
 MPTABLE: 0:28 INTA routed to irq 11 
 
 pcib2: slot 0 INTA is routed to irq 11 
 
 pci2: <network> (vendor 0x8086, dev 0x4237) at device 0.0 irq 11 
 
 pci2: <PCI bus> [attached!] on pcib2 
 
 pcib2: <MPTABLE PCI-PCI bridge> [attached!] irq 11 at device 28.1 on pci0 
 
 pcib3.pci0.pcib0.legacy0.nexus0.root0 
 
 pcib3: <MPTABLE PCI-PCI bridge> [tentative] irq 10 at device 28.2 on pci0 
 
 pcib3:     domain              0 
 
 pcib3:     secondary bus       3 
 
 pcib3:     subordinate bus     67 
 
 pcib3:     I/O decode          0x5000-0x6fff 
 
 pcib3:     memory decode       0x94700000-0x986fffff 
 
 pcib3:     no prefetched decode 
 
 pcib3: Disable PCI Express hot-plug interrupts(0x0009) 
 
 pci3.pcib3.pci0.pcib0.legacy0.nexus0.root0 
 
 pci3: <PCI bus> [tentative] on pcib3 
 
 pci3: domain=0, physical bus=3 
 
 pci3: <PCI bus> [attached!] on pcib3 
 
 pcib3: <MPTABLE PCI-PCI bridge> [attached!] irq 10 at device 28.2 on pci0 
 
 pcib4.pci0.pcib0.legacy0.nexus0.root0 
 
 pcib4: <MPTABLE PCI-PCI bridge> [tentative] irq 10 at device 28.4 on pci0 
 
 pcib4:     domain              0 
 
 pcib4:     secondary bus       68 
 
 pcib4:     subordinate bus     132 
 
 pcib4:     I/O decode          0x3000-0x4fff 
 
 pcib4:     memory decode       0x90700000-0x946fffff 
 
 pcib4:     no prefetched decode 
 
 pcib4: Disable PCI Express hot-plug interrupts(0x0009) 
 
 pci68.pcib4.pci0.pcib0.legacy0.nexus0.root0 
 
 pci68: <PCI bus> [tentative] on pcib4 
 
 pci68: domain=0, physical bus=68 
 
 pci68: <PCI bus> [attached!] on pcib4 
 
 pcib4: <MPTABLE PCI-PCI bridge> [attached!] irq 10 at device 28.4 on pci0 
 
 pcib5.pci0.pcib0.legacy0.nexus0.root0 
 
 pcib5: <MPTABLE PCI-PCI bridge> [tentative] irq 11 at device 28.5 on pci0 
 
 pcib5:     domain              0 
 
 pcib5:     secondary bus       133 
 
 pcib5:     subordinate bus     133 
 
 pcib5:     I/O decode          0x2000-0x2fff 
 
 pcib5:     memory decode       0x90600000-0x906fffff 
 
 pcib5:     no prefetched decode 
 
 pcib5: Disable PCI Express hot-plug interrupts(0x0009) 
 
 pci133.pcib5.pci0.pcib0.legacy0.nexus0.root0 
 
 pci133: <PCI bus> [tentative] on pcib5 
 
 pci133: domain=0, physical bus=133 
 
 found-> 	 vendor=0x11ab, dev=0x436c, revid=0x10 
	 
	 domain=0, bus=133, slot=0, func=0 
	 
	 class=02-00-00, hdrtype=0x00, mfdev=0 
	 
	 cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords) 
	 
	 lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) 
	 
	 intpin=a, irq=11 
	 
	 powerspec 3    supports D0 D1 D2 D3    current D0 
	 
	 MSI supports 1 message, 64 bit 
	 
	 PCI Express ver.2 cap=0x0012[LEGDEV] 
	 
	 map[10]: type Memory, range 64, base 0x90600000, size 14, enabled 
 
 pcib5: requested memory range 0x90600000-0x90603fff: good 
	 
	 map[18]: type I/O Port, range 32, base 0x2000, size    8, enabled 
 
 pcib5: requested I/O range 0x2000-0x20ff: in range 
 
 MPTABLE: fixed interrupt routing for 0:28 INTA 
 
 MPTABLE: 0:28 INTA routed to irq 11 
 
 pcib5: slot 0 INTA is routed to irq 11 
 
 mskc0.pci133.pcib5.pci0.pcib0.legacy0.nexus0.root0 
 
 mskc0: <Marvell Yukon 88E8072 Gigabit Ethernet> [tentative] port 0x2000-0x20ff mem 0x90600000-0x90603fff irq 11 at device 0.0 on pci133 
 
 mskc0: Reserved 0x4000 bytes for rid 0x10 type 3 at 0x90600000 
 
 mskc0: RAM buffer size : 0KB 
 
 msk0.mskc0.pci133.pcib5.pci0.pcib0.legacy0.nexus0.root0 
 
 msk0: <Marvell Technology Group Ltd. Yukon EX Id 0xb5 Rev 0x02> [tentative] on mskc0 
 
 alignment check failed 
 
 alignment check failed 
 
 miibus0.msk0.mskc0.pci133.pcib5.pci0.pcib0.legacy0.nexus0.root0 
 
 miibus0: <MII bus> [tentative] on msk0 
 
 e1000phy0.miibus0.msk0.mskc0.pci133.pcib5.pci0.pcib0.legacy0.nexus0.root0 
 
 e1000phy0: <Marvell 88E1149 Gigabit PHY> [tentative] on miibus0 
 
 e1000phy0:    10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto 
 
 e1000phy0: <Marvell 88E1149 Gigabit PHY> [attached!] on miibus0 
 
 miibus0: <MII bus> [attached!] on msk0 
 
 msk0: bpf attached 
 
 msk0: MAC address: 18:a9:05:cf:b6:67 
 
 msk0: <Marvell Technology Group Ltd. Yukon EX Id 0xb5 Rev 0x02> [attached!] on mskc0 
 
 mskc0: <Marvell Yukon 88E8072 Gigabit Ethernet> [attached!] port 0x2000-0x20ff mem 0x90600000-0x90603fff irq 11 at device 0.0 on pci133 
 
 pci133: <PCI bus> [attached!] on pcib5 
 
 pcib5: <MPTABLE PCI-PCI bridge> [attached!] irq 11 at device 28.5 on pci0 
 
 uhci3.pci0.pcib0.legacy0.nexus0.root0 
 
 uhci3: <Intel 82801I (ICH9) USB controller> [tentative] port 0x7060-0x707f irq 10 at device 29.0 on pci0 
 
 uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0x7060 
 
 usb4.uhci3.pci0.pcib0.legacy0.nexus0.root0 
 
 usb4: <Intel 82801I (ICH9) USB controller> [tentative] on uhci3 
 
 usb4: USB revision 1.0 
 
 uhub4.usb4.uhci3.pci0.pcib0.legacy0.nexus0.root0 
 
 uhub4: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [tentative] on usb4 
 
 uhub4: 2 ports with 2 removable, self powered 
 
 uhub4: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [attached!] on usb4 
 
 usb4: <Intel 82801I (ICH9) USB controller> [attached!] on uhci3 
 
 uhci3: <Intel 82801I (ICH9) USB controller> [attached!] port 0x7060-0x707f irq 10 at device 29.0 on pci0 
 
 uhci4.pci0.pcib0.legacy0.nexus0.root0 
 
 uhci4: <Intel 82801I (ICH9) USB controller> [tentative] port 0x7040-0x705f irq 10 at device 29.1 on pci0 
 
 uhci4: Reserved 0x20 bytes for rid 0x20 type 4 at 0x7040 
 
 usb5.uhci4.pci0.pcib0.legacy0.nexus0.root0 
 
 usb5: <Intel 82801I (ICH9) USB controller> [tentative] on uhci4 
 
 usb5: USB revision 1.0 
 
 uhub5.usb5.uhci4.pci0.pcib0.legacy0.nexus0.root0 
 
 uhub5: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [tentative] on usb5 
 
 uhub5: 2 ports with 2 removable, self powered 
 
 uhub5: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [attached!] on usb5 
 
 usb5: <Intel 82801I (ICH9) USB controller> [attached!] on uhci4 
 
 uhci4: <Intel 82801I (ICH9) USB controller> [attached!] port 0x7040-0x705f irq 10 at device 29.1 on pci0 
 
 uhci5.pci0.pcib0.legacy0.nexus0.root0 
 
 uhci5: <Intel 82801I (ICH9) USB controller> [tentative] port 0x7020-0x703f irq 10 at device 29.2 on pci0 
 
 uhci5: Reserved 0x20 bytes for rid 0x20 type 4 at 0x7020 
 
 usb6.uhci5.pci0.pcib0.legacy0.nexus0.root0 
 
 usb6: <Intel 82801I (ICH9) USB controller> [tentative] on uhci5 
 
 usb6: USB revision 1.0 
 
 uhub6.usb6.uhci5.pci0.pcib0.legacy0.nexus0.root0 
 
 uhub6: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [tentative] on usb6 
 
 uhub6: 2 ports with 2 removable, self powered 
 
 uhub6: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [attached!] on usb6 
 
 usb6: <Intel 82801I (ICH9) USB controller> [attached!] on uhci5 
 
 uhci5: <Intel 82801I (ICH9) USB controller> [attached!] port 0x7020-0x703f irq 10 at device 29.2 on pci0 
 
 ehci1.pci0.pcib0.legacy0.nexus0.root0 
 
 ehci1: <EHCI (generic) USB 2.0 controller> [tentative] mem 0x98904800-0x98904bff irq 10 at device 29.7 on pci0 
 
 ehci1: Reserved 0x400 bytes for rid 0x10 type 3 at 0x98904800 
 
 usb7: EHCI version 1.0 
 
 usb7: companion controllers, 2 ports each: usb4 usb5 usb6 
 
 usb7.ehci1.pci0.pcib0.legacy0.nexus0.root0 
 
 usb7: <EHCI (generic) USB 2.0 controller> [tentative] on ehci1 
 
 usb7: USB revision 2.0 
 
 uhub7.usb7.ehci1.pci0.pcib0.legacy0.nexus0.root0 
 
 uhub7: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> [tentative] on usb7 
 
 uhub7: 6 ports with 6 removable, self powered 
 
 uhub7: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> [attached!] on usb7 
 
 usb7: <EHCI (generic) USB 2.0 controller> [attached!] on ehci1 
 
 ehci1: <EHCI (generic) USB 2.0 controller> [attached!] mem 0x98904800-0x98904bff irq 10 at device 29.7 on pci0 
 
 pcib6.pci0.pcib0.legacy0.nexus0.root0 
 
 pcib6: <MPTABLE PCI-PCI bridge> [tentative] at device 30.0 on pci0 
 
 pcib6:     domain              0 
 
 pcib6:     secondary bus       134 
 
 pcib6:     subordinate bus     134 
 
 pcib6:     I/O decode          0xf000-0xfff 
 
 pcib6:     memory decode       0x90500000-0x905fffff 
 
 pcib6:     no prefetched decode 
 
 pcib6:     Subtractively decoded bridge. 
 
 pci134.pcib6.pci0.pcib0.legacy0.nexus0.root0 
 
 pci134: <PCI bus> [tentative] on pcib6 
 
 pci134: domain=0, physical bus=134 
 
 pci134: <PCI bus> [attached!] on pcib6 
 
 pcib6: <MPTABLE PCI-PCI bridge> [attached!] at device 30.0 on pci0 
 
 isab0.pci0.pcib0.legacy0.nexus0.root0 
 
 isab0: <PCI-ISA bridge> [tentative] at device 31.0 on pci0 
 
 isa0.isab0.pci0.pcib0.legacy0.nexus0.root0 
 
 isa0: <ISA bus> [tentative] on isab0 
 
 isa0: <ISA bus> [attached!] on isab0 
 
 isab0: <PCI-ISA bridge> [attached!] at device 31.0 on pci0 
 
 ahci0.pci0.pcib0.legacy0.nexus0.root0 
 
 ahci0: <AHCI-PCI-SATA> [tentative] port 0x7000-0x701f,0x70f8-0x70fb,0x70e0-0x70e7,0x70fc-0x70ff,0x70e8-0x70ef mem 0x98904000-0x989047ff irq 10 at device 31.2 on pci0 
 
 ahci0: attempting to allocate 1 MSI vector (16 supported) 
 
 alloc MSI intr 24 on cpu0 
 
 ahci0: using IRQ 24 on cpu0 for MSI 
 
 ahci0: Reserved 0x800 bytes for rid 0x24 type 3 at 0x98904000 
 
 ahci0: Intel hocus pocus 
 
 ahci0: AHCI 1.2 capabilities 0xef20ffc3<S64A,NCQ,SSNTF,SSS,SALP,SAL,SCLO,PMD,SSC,PSC,CCCS,EMS>, 4 ports, 32 tags/port, gen 2 (3Gbps) 
 
 ahci0.0: Caps 4<POD> 
 
 ahci0.1: Caps 4<POD> 
 
 ahci0.5: Caps 40004<HPCP,POD> 
 
 ahci0.1: START HARDRESET 
 
 ahci0.0: START HARDRESET 
 
 map MSI intr 24 on cpu0 
 
 ahci0.5: START HARDRESET 
 
 ahci0.0: END HARDRESET 0 
 
 ahci0.1: END HARDRESET 0 
 
 ahci0.0: START SOFTRESET c017<CR,FR,FRE,POD,SUD,ST> 
 
 ahci0.1: START SOFTRESET c017<CR,FR,FRE,POD,SUD,ST> 
 
 ahci0.1: sig eb140101 
 
 ahci0.0: sig 00000101 
 
 ahci0.1: END SOFTRESET 
 
 ahci0.0: END SOFTRESET 
 
 ahci0.0: Found DISK "ST9250410AS 0006HPM1" serial="5VG1L845" 
 
 ahci0.0: tags=32/32 satacap=0d06 satafea=004c NCQ=YES capacity=238475.17MB 
 
 ahci0.0: f85=3069 f86=bc09 f87=6123 WC=enabled RA=enabled SEC=frozen 
 
 ahci0.0: Set dummy xfer mode to 45 
 
 (probe0:ahci0:0:1:0): error 22 
 
 (probe0:ahci0:0:1:0): Unretryable Error 
 
 (probe0:ahci0:0:2:0): error 22 
 
 (probe0:ahci0:0:2:0): Unretryable Error 
 
 (probe0:ahci0:0:3:0): error 22 
 
 (probe0:ahci0:0:3:0): Unretryable Error 
 
 (probe0:ahci0:0:4:0): error 22 
 
 (probe0:ahci0:0:4:0): Unretryable Error 
 
 (probe0:ahci0:0:5:0): error 22 
 
 (probe0:ahci0:0:5:0): Unretryable Error 
 
 (probe0:ahci0:0:6:0): error 22 
 
 (probe0:ahci0:0:6:0): Unretryable Error 
 
 (probe0:ahci0:0:7:0): error 22 
 
 (probe0:ahci0:0:7:0): Unretryable Error 
 
 (probe0:ahci0:0:8:0): error 22 
 
 (probe0:ahci0:0:8:0): Unretryable Error 
 
 (probe0:ahci0:0:9:0): error 22 
 
 (probe0:ahci0:0:9:0): Unretryable Error 
 
 (probe0:ahci0:0:10:0): error 22 
 
 (probe0:ahci0:0:10:0): Unretryable Error 
 
 (probe0:ahci0:0:11:0): error 22 
 
 (probe0:ahci0:0:11:0): Unretryable Error 
 
 (probe0:ahci0:0:12:0): error 22 
 
 (probe0:ahci0:0:12:0): Unretryable Error 
 
 (probe0:ahci0:0:13:0): error 22 
 
 (probe0:ahci0:0:13:0): Unretryable Error 
 
 (probe0:ahci0:0:14:0): error 22 
 
 (probe0:ahci0:0:14:0): Unretryable Error 
 
 ahci0.1: Found ATAPI "hp         DVDRAM GT20L DC05" serial="M3Z9AM20223" 
 
 ahci0.1: tags=0/32 satacap=0402 satafea=0068 NCQ=NO capacity=1.00MB 
 
 ahci0.1: f85=4210 f86=0000 f87=4000 WC=notsupp RA=notsupp SEC=notsupp 
 
 ahci0.1: Set dummy xfer mode to 45 
 
 ahci0.1: TFES slot 5 ci_saved = 00000020 
 
 ahci0.1: Copying rfis slot 5 
 
 ahci0.1: Shortening sense request 
 
 (probe0:ahci0:1:0:0): Retrying Command 
 
 (probe0:ahci0:1:0:0): error 22 
 
 (probe0:ahci0:1:0:0): Unretryable Error 
 
 ahci0.1: TFES slot 7 ci_saved = 00000080 
 
 ahci0.1: Copying rfis slot 7 
 
 (probe0:ahci0:1:1:0): error 22 
 
 (probe0:ahci0:1:1:0): Unretryable Error 
 
 (probe0:ahci0:1:2:0): error 22 
 
 (probe0:ahci0:1:2:0): Unretryable Error 
 
 (probe0:ahci0:1:3:0): error 22 
 
 (probe0:ahci0:1:3:0): Unretryable Error 
 
 (probe0:ahci0:1:4:0): error 22 
 
 (probe0:ahci0:1:4:0): Unretryable Error 
 
 (probe0:ahci0:1:5:0): error 22 
 
 (probe0:ahci0:1:5:0): Unretryable Error 
 
 (probe0:ahci0:1:6:0): error 22 
 
 (probe0:ahci0:1:6:0): Unretryable Error 
 
 (probe0:ahci0:1:7:0): error 22 
 
 (probe0:ahci0:1:7:0): Unretryable Error 
 
 (probe0:ahci0:1:8:0): error 22 
 
 (probe0:ahci0:1:8:0): Unretryable Error 
 
 (probe0:ahci0:1:9:0): error 22 
 
 (probe0:ahci0:1:9:0): Unretryable Error 
 
 (probe0:ahci0:1:10:0): error 22 
 
 (probe0:ahci0:1:10:0): Unretryable Error 
 
 (probe0:ahci0:1:11:0): error 22 
 
 (probe0:ahci0:1:11:0): Unretryable Error 
 
 (probe0:ahci0:1:12:0): error 22 
 
 (probe0:ahci0:1:12:0): Unretryable Error 
 
 (probe0:ahci0:1:13:0): error 22 
 
 (probe0:ahci0:1:13:0): Unretryable Error 
 
 (probe0:ahci0:1:14:0): error 22 
 
 (probe0:ahci0:1:14:0): Unretryable Error 
 
 ahci0.5: Port appears to be unplugged 
 
 ahci0.5: No device detected 
 
 ahci0.5: END HARDRESET 19 
 
 (probe0:ahci0:5:0:0): error 22 
 
 (probe0:ahci0:5:0:0): Unretryable Error 
 
 (probe0:ahci0:5:1:0): error 22 
 
 (probe0:ahci0:5:1:0): Unretryable Error 
 
 (probe0:ahci0:5:2:0): error 22 
 
 (probe0:ahci0:5:2:0): Unretryable Error 
 
 (probe0:ahci0:5:3:0): error 22 
 
 (probe0:ahci0:5:3:0): Unretryable Error 
 
 (probe0:ahci0:5:4:0): error 22 
 
 (probe0:ahci0:5:4:0): Unretryable Error 
 
 (probe0:ahci0:5:5:0): error 22 
 
 (probe0:ahci0:5:5:0): Unretryable Error 
 
 (probe0:ahci0:5:6:0): error 22 
 
 (probe0:ahci0:5:6:0): Unretryable Error 
 
 (probe0:ahci0:5:7:0): error 22 
 
 (probe0:ahci0:5:7:0): Unretryable Error 
 
 (probe0:ahci0:5:8:0): error 22 
 
 (probe0:ahci0:5:8:0): Unretryable Error 
 
 (probe0:ahci0:5:9:0): error 22 
 
 (probe0:ahci0:5:9:0): Unretryable Error 
 
 (probe0:ahci0:5:10:0): error 22 
 
 (probe0:ahci0:5:10:0): Unretryable Error 
 
 (probe0:ahci0:5:11:0): error 22 
 
 (probe0:ahci0:5:11:0): Unretryable Error 
 
 (probe0:ahci0:5:12:0): error 22 
 
 (probe0:ahci0:5:12:0): Unretryable Error 
 
 (probe0:ahci0:5:13:0): error 22 
 
 (probe0:ahci0:5:13:0): Unretryable Error 
 
 (probe0:ahci0:5:14:0): error 22 
 
 (probe0:ahci0:5:14:0): Unretryable Error 
 
 ahci0: <AHCI-PCI-SATA> [attached!] port 0x7000-0x701f,0x70f8-0x70fb,0x70e0-0x70e7,0x70fc-0x70ff,0x70e8-0x70ef mem 0x98904000-0x989047ff irq 24,10 at device 31.2 on pci0 
 
 pci0: <PCI bus> [attached!] on pcib0 
 
 pcib0: <MPTABLE Host-PCI bridge> [attached!] pcibus 0 on motherboard 
 
 Trying Read_Port at 203 
 
 Trying Read_Port at 243 
 
 Trying Read_Port at 283 
 
 Trying Read_Port at 2c3 
 
 Trying Read_Port at 303 
 
 Trying Read_Port at 343 
 
 Trying Read_Port at 383 
 
 Trying Read_Port at 3c3 
 
 ex_isa_identify() 
 
 isa_probe_children: disabling PnP devices 
 
 isa_probe_children: probing non-PnP devices 
 
 orm0.isa0.isab0.pci0.pcib0.legacy0.nexus0.root0 
 
 orm0: <Option ROMs> [tentative] at iomem 0xd0000-0xd0fff,0xd1000-0xd1fff on isa0 
 
 orm0: <Option ROMs> [attached!] at iomem 0xd0000-0xd0fff,0xd1000-0xd1fff on isa0 
 
 adv0 [tentative] failed to probe on isa0 
 
 bt0: Failed Status Reg Test - ff 
 
 bt_isa_probe: Probe failed at 0x330 
 
 bt0: Failed Status Reg Test - ff 
 
 bt_isa_probe: Probe failed at 0x334 
 
 bt0: Failed Status Reg Test - ff 
 
 bt_isa_probe: Probe failed at 0x230 
 
 bt0: Failed Status Reg Test - ff 
 
 bt_isa_probe: Probe failed at 0x234 
 
 bt0: Failed Status Reg Test - ff 
 
 bt_isa_probe: Probe failed at 0x130 
 
 bt0: Failed Status Reg Test - ff 
 
 bt_isa_probe: Probe failed at 0x134 
 
 bt0 [tentative] failed to probe at port 0x134-0x137 on isa0 
 
 atkbdc0.isa0.isab0.pci0.pcib0.legacy0.nexus0.root0 
 
 atkbdc0: <Keyboard controller (i8042)> [tentative] at port 0x60,0x64 on isa0 
 
 atkbd0.atkbdc0.isa0.isab0.pci0.pcib0.legacy0.nexus0.root0 
 
 atkbd0: <AT Keyboard> [tentative] flags 0x1 irq 1 on atkbdc0 
 
 atkbd: the current kbd controller command byte 0067 
 
 atkbd: keyboard ID 0x41ab (2) 
 
 kbd0 at atkbd0 
 
 kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000 
 
 atkbd0: <AT Keyboard> [attached!] flags 0x1 irq 1 on atkbdc0 
 
 psm0: current command byte:0067 
 
 psm0.atkbdc0.isa0.isab0.pci0.pcib0.legacy0.nexus0.root0 
 
 psm0: <PS/2 Mouse> [tentative] irq 12 on atkbdc0 
 
 psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons 
 
 psm0: config:00000000, flags:00000008, packet size:3 
 
 psm0: syncmask:c0, syncbits:00 
 
 psm0: <PS/2 Mouse> [attached!] irq 12 on atkbdc0 
 
 atkbdc0: <Keyboard controller (i8042)> [attached!] at port 0x60,0x64 on isa0 
 
 vga0.isa0.isab0.pci0.pcib0.legacy0.nexus0.root0 
 
 vga0: <Generic ISA VGA> [tentative] at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 
 
 fb0: vga0, vga, type:VGA (5), flags:0x7007f 
 
 fb0: port:0x3c0-0x3df, mem:0xa0000 0x20000 
 
 fb0: init mode:24, bios mode:3, current mode:24 
 
 fb0: window:0xffffffff800b8000 size:32k gran:32k, buf:0 size:32k 
 
 VGA parameters upon power-up 
  
  50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 
  
  bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 
  
  b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
  
  3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
 
 VGA parameters in BIOS for mode 24 
  
  50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 
  
  bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 
  
  b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
  
  3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
 
 VGA parameters to be used for mode 24 
  
  50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 
  
  bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 
  
  b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
  
  3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
 
 vga0: <Generic ISA VGA> [attached!] at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 
 
 sc0.isa0.isab0.pci0.pcib0.legacy0.nexus0.root0 
 
 sc0: <System console> [tentative] at flags 0x100 on isa0 
 
 sc0: VGA <16 virtual consoles, flags=0x300> 
 
 sc0: fb0, kbd1, terminal emulator: sc (syscons terminal) 
 
 sc0: <System console> [attached!] at flags 0x100 on isa0 
 
 lm0 [tentative] failed to probe at port 0x290-0x297 on isa0 
 
 it0 [tentative] failed to probe at port 0x290-0x297 on isa0 
 
 it1 [tentative] failed to probe at port 0xc00-0xc07 on isa0 
 
 it2 [tentative] failed to probe at port 0xd00-0xd07 on isa0 
 
 it3 [tentative] failed to probe at port 0x228-0x22f on isa0 
 
 wbsio0 [tentative] failed to probe at port 0x2e-0x2f on isa0 
 
 wbsio1 [tentative] failed to probe at port 0x4e-0x4f on isa0 
 
 sio0: can't drain, serial port might not exist, disabling 
 
 sio0 [tentative] failed to probe at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 
 
 sio1: can't drain, serial port might not exist, disabling 
 
 sio1 [tentative] failed to probe at port 0x2f8-0x2ff irq 3 on isa0 
 
 sio2: not probed (disabled) 
 
 sio3: not probed (disabled) 
 
 ppc0: cannot reserve I/O port range 
 
 ppc0: <Parallel port> [tentative] failed to probe at irq 7 on isa0 
 
 ed0: not probed (disabled) 
 
 lnc0: not probed (disabled) 
 
 cs0: not probed (disabled) 
 
 sn0: not probed (disabled) 
 
 isa_probe_children: probing PnP devices 
 
 ndepotmags=6     x mag_cap=22    for nameibufs 
 
 ndepotmags=6     x mag_cap=22    for NFS mount 
 
 ndepotmags=6     x mag_cap=22    for NFS node 
 
 ndepotmags=6     x mag_cap=46    for vnodes 
 
 lo0: bpf attached 
 
 ppp0: bpf attached 
 
 sl0: bpf attached 
 
 ndepotmags=6     x mag_cap=22    for UFS dirhash 
 
 faith0: bpf attached 
 
 hptrr: no controller detected. 
 
 hpt27xx: no controller detected. 
 
 CAM: Configuring bus: ahci0 
 
 CAM: Configuring bus: ahci0 
 
 CAM: Configuring bus: ahci0 
 
 CAM: Configuring 3 busses 
 
 (probe0:ahci0:0:1:0): error 22 
 
 (probe0:ahci0:0:1:0): Unretryable Error 
 
 (probe0:ahci0:0:2:0): error 22 
 
 (probe0:ahci0:0:2:0): Unretryable Error 
 
 (probe0:ahci0:0:3:0): error 22 
 
 (probe0:ahci0:0:3:0): Unretryable Error 
 
 (probe0:ahci0:0:4:0): error 22 
 
 (probe0:ahci0:0:4:0): Unretryable Error 
 
 (probe0:ahci0:0:5:0): error 22 
 
 (probe0:ahci0:0:5:0): Unretryable Error 
 
 (probe0:ahci0:0:6:0): error 22 
 
 (probe0:ahci0:0:6:0): Unretryable Error 
 
 (probe0:ahci0:0:7:0): error 22 
 
 (probe0:ahci0:0:7:0): Unretryable Error 
 
 (probe0:ahci0:0:8:0): error 22 
 
 (probe0:ahci0:0:8:0): Unretryable Error 
 
 (probe0:ahci0:0:9:0): error 22 
 
 (probe0:ahci0:0:9:0): Unretryable Error 
 
 (probe0:ahci0:0:10:0): error 22 
 
 (probe0:ahci0:0:10:0): Unretryable Error 
 
 (probe0:ahci0:0:11:0): error 22 
 
 (probe0:ahci0:0:11:0): Unretryable Error 
 
 (probe0:ahci0:0:12:0): error 22 
 
 (probe0:ahci0:0:12:0): Unretryable Error 
 
 (probe0:ahci0:0:13:0): error 22 
 
 (probe0:ahci0:0:13:0): Unretryable Error 
 
 (probe0:ahci0:0:14:0): error 22 
 
 (probe0:ahci0:0:14:0): Unretryable Error 
 
 CAM: Finished configuring bus: ahci0 
 
 (probe2:ahci0:5:0:0): error 22 
 
 (probe2:ahci0:5:0:0): Unretryable Error 
 
 (probe0:ahci0:5:1:0): error 22 
 
 (probe0:ahci0:5:1:0): Unretryable Error 
 
 (probe0:ahci0:5:2:0): error 22 
 
 (probe0:ahci0:5:2:0): Unretryable Error 
 
 (probe0:ahci0:5:3:0): error 22 
 
 (probe0:ahci0:5:3:0): Unretryable Error 
 
 (probe0:ahci0:5:4:0): error 22 
 
 (probe0:ahci0:5:4:0): Unretryable Error 
 
 (probe0:ahci0:5:5:0): error 22 
 
 (probe0:ahci0:5:5:0): Unretryable Error 
 
 (probe0:ahci0:5:6:0): error 22 
 
 (probe0:ahci0:5:6:0): Unretryable Error 
 
 (probe0:ahci0:5:7:0): error 22 
 
 (probe0:ahci0:5:7:0): Unretryable Error 
 
 (probe0:ahci0:5:8:0): error 22 
 
 (probe0:ahci0:5:8:0): Unretryable Error 
 
 (probe0:ahci0:5:9:0): error 22 
 
 (probe0:ahci0:5:9:0): Unretryable Error 
 
 (probe0:ahci0:5:10:0): error 22 
 
 (probe0:ahci0:5:10:0): Unretryable Error 
 
 (probe0:ahci0:5:11:0): error 22 
 
 (probe0:ahci0:5:11:0): Unretryable Error 
 
 (probe0:ahci0:5:12:0): error 22 
 
 (probe0:ahci0:5:12:0): Unretryable Error 
 
 (probe0:ahci0:5:13:0): error 22 
 
 (probe0:ahci0:5:13:0): Unretryable Error 
 
 (probe0:ahci0:5:14:0): error 22 
 
 (probe0:ahci0:5:14:0): Unretryable Error 
 
 CAM: Finished configuring bus: ahci0 
 
 ahci0.1: TFES slot 8 ci_saved = 00000100 
 
 ahci0.1: Copying rfis slot 8 
 
 ahci0.1: TFES slot 11 ci_saved = 00000800 
 
 ahci0.1: Copying rfis slot 11 
 
 ahci0.1: Shortening sense request 
 
 (probe1:ahci0:1:0:0): Retrying Command 
 
 (probe1:ahci0:1:0:0): error 22 
 
 (probe1:ahci0:1:0:0): Unretryable Error 
 
 ahci0.1: TFES slot 13 ci_saved = 00002000 
 
 ahci0.1: Copying rfis slot 13 
 
 (probe0:ahci0:1:1:0): error 22 
 
 (probe0:ahci0:1:1:0): Unretryable Error 
 
 (probe0:ahci0:1:2:0): error 22 
 
 (probe0:ahci0:1:2:0): Unretryable Error 
 
 (probe0:ahci0:1:3:0): error 22 
 
 (probe0:ahci0:1:3:0): Unretryable Error 
 
 (probe0:ahci0:1:4:0): error 22 
 
 (probe0:ahci0:1:4:0): Unretryable Error 
 
 (probe0:ahci0:1:5:0): error 22 
 
 (probe0:ahci0:1:5:0): Unretryable Error 
 
 (probe0:ahci0:1:6:0): error 22 
 
 (probe0:ahci0:1:6:0): Unretryable Error 
 
 (probe0:ahci0:1:7:0): error 22 
 
 (probe0:ahci0:1:7:0): Unretryable Error 
 
 (probe0:ahci0:1:8:0): error 22 
 
 (probe0:ahci0:1:8:0): Unretryable Error 
 
 (probe0:ahci0:1:9:0): error 22 
 
 (probe0:ahci0:1:9:0): Unretryable Error 
 
 (probe0:ahci0:1:10:0): error 22 
 
 (probe0:ahci0:1:10:0): Unretryable Error 
 
 (probe0:ahci0:1:11:0): error 22 
 
 (probe0:ahci0:1:11:0): Unretryable Error 
 
 (probe0:ahci0:1:12:0): error 22 
 
 (probe0:ahci0:1:12:0): Unretryable Error 
 
 (probe0:ahci0:1:13:0): error 22 
 
 (probe0:ahci0:1:13:0): Unretryable Error 
 
 (probe0:ahci0:1:14:0): error 22 
 
 (probe0:ahci0:1:14:0): Unretryable Error 
 
 CAM: Finished configuring bus: ahci0 
 
 CAM: finished configuring all busses 
 
 no B_DEVMAGIC (bootdev=0) 
 
 pass0 at ahci0 bus 0 target 0 lun 0 
 
 ATA PseudoRAID loaded 
 
 pass0: <SATA ST9250410AS 0006> Fixed Direct Access SCSI-4 device  
  
 pass0: Serial Number 5VG1L845 
 
 pass0: 300.000MB/s transfers 
 
 pass1 at ahci0 bus 1 target 0 lun 0 
 
 pass1: <hp DVDRAM GT20L DC05> Removable CD-ROM SCSI-0 device  
  
 pass1: 150.000MB/s transfers 
 
 sg0 at ahci0 bus 0 target 0 lun 0 
 
 sg0: <SATA ST9250410AS 0006> Fixed Direct Access SCSI-4 device  
  
 sg0: Serial Number 5VG1L845 
 
 sg0: 300.000MB/s transfers 
 
 sg1 at ahci0 bus 1 target 0 lun 0 
 
 sg1: <hp DVDRAM GT20L DC05> Removable CD-ROM SCSI-0 device  
  
 sg1: 150.000MB/s transfers 
 
 No policy for da0 specified, or policy not found 
 
 disk scheduler: set policy of da0 to noop 
 
 No policy for cd0 specified, or policy not found 
 
 disk scheduler: set policy of cd0 to noop 
 
 da0 at ahci0 bus 0 target 0 lun 0 
 
 da0: <SATA ST9250410AS 0006> Fixed Direct Access SCSI-4 device  
  
 da0: Serial Number 5VG1L845 
 
 da0: 300.000MB/s transfers 
 
 da0: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C) 
 
 ahci0.1: TFES slot 14 ci_saved = 00004000 
 
 ahci0.1: Copying rfis slot 14 
 
 ahci0.1: Shortening sense request 
 
 (cd0:ahci0:1:0:0): Retrying Command 
 
 (cd0:ahci0:1:0:0): error 6 
 
 (cd0:ahci0:1:0:0): Unretryable Error 
 
 cd0 at ahci0 bus 1 target 0 lun 0 
 
 cd0: <hp DVDRAM GT20L DC05> Removable CD-ROM SCSI-0 device  
  
 cd0: 150.000MB/s transfers 
 
 cd0: Attempt to query device size failed: NOT READY, Medium not present - tray closed 
 
 da0: type 0xa5, start 63, end = 488388095, size 488388033 : OK 
 
 Mounting root from hammer:serno/5VG1L845.s1d 
 
 HAMMER(ROOT) recovery check seqno=0010ca77 
 
 HAMMER(ROOT) recovery range 3000000001dea7b8-3000000001dea7b8 
 
 HAMMER(ROOT) recovery nexto 3000000001dea7b8 endseqno=0010ca78 
 
 HAMMER(ROOT) mounted clean, no recovery needed 
 
 DMA space used: 4208k, remaining available: 16384k 
 
 Mounting devfs 
 
 start_init: trying /sbin/init 
 

Back