Project

General

Profile

Bug #2298 » dmesg.txt

phma, 02/03/2012 01:15 AM

 
Copyright (c) 2003-2012 The DragonFly Project.
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
MPTABLE: warning duplicated PCI int entry for bus 0, dev 29, pin 0
MPTABLE: warning duplicated PCI int entry for bus 0, dev 31, pin 1
MPTABLE: warning PCI int dst apic id 1 does not exist
DragonFly v3.1.0.93.g7ca562-DEVELOPMENT #3: Wed Feb 1 17:39:54 EST 2012
phma@darner.ixazon.lan:/usr/obj/usr/src/sys/GENERIC
TSC clock: 2792946176 Hz, i8254 clock: 1193159 Hz
CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz (2793.01-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf29 Stepping = 9
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x4400<CNXT-ID,xTPR>
real memory = 1071708160 (1022 MB)
avail memory = 1016315904 (969 MB)
lapic: divisor index 0, frequency 99750380 Hz
Initialize MI interrupts
FQ scheduler policy version 1.1 loaded
kbd1 at kbdmux0
disk scheduler: set policy of md0 to noop
md0: Malloc disk
ACPI: RSDP 0xf64a0 00014 (v0 PTLTD )
ACPI: RSDT 0x3fe7509c 00038 (v1 PTLTD RSDT 060400D0 LTP 00000000)
ACPI: FACP 0x3fe79e93 00074 (v1 IBM THINKCEN 060400D0 PTL 00000001)
ACPI: DSDT 0x3fe750d4 04DBF (v1 IBM THINKCEN 060400D0 MSFT 0100000E)
ACPI: FACS 0x3fe7afc0 00040
ACPI: TCPA 0x3fe79f07 00032 (v1 IBM THINKCEN 060400D0 PTL 00000001)
ACPI: APIC 0x3fe79f39 00068 (v1 PTLTD ? APIC 060400D0 LTP 00000000)
ACPI: BOOT 0x3fe79fa1 00028 (v1 PTLTD $SBFTBL$ 060400D0 LTP 00000001)
ACPI: SSDT 0x3fe79fc9 00037 (v1 PTLTD ACPIHT 060400D0 LTP 00000001)
npx0: <math processor> on motherboard
npx0: INT 16 interface
Using XMM optimized bcopy/copyin/copyout
cryptosoft0: <software crypto> on motherboard
acpi0: <PTLTD RSDT> on motherboard
ACPI FADT: SCI testing interrupt mode ...
sched_ithd: stray interrupt 9 on cpu0
ACPI FADT: SCI select level/high
objcache_reclaimlist
objcache_reclaimlist
objcache_reclaimlist
objcache_reclaimlist
acpi0: Power Button (fixed)
Warning: ACPI is disabling APM's device. You can't run both
[ACPI Debug] Buffer [0x6]
0: 23 00 08 18 79 00 #...y.
[ACPI Debug] Buffer [0x6]
0: 23 01 00 18 79 00 #...y.
[ACPI Debug] Buffer [0x6]
0: 23 01 00 18 79 00 #...y.
[ACPI Debug] Buffer [0x6]
0: 23 01 00 18 79 00 #...y.
[ACPI Debug] Buffer [0x6]
0: 23 00 02 18 79 00 #...y.
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
[ACPI Debug] Buffer [0x6]
0: 23 00 08 18 79 00 #...y.
[ACPI Debug] Buffer [0x6]
0: 23 00 08 18 79 00 #...y.
[ACPI Debug] Buffer [0x6]
0: 23 01 00 18 79 00 #...y.
[ACPI Debug] Buffer [0x6]
0: 23 01 00 18 79 00 #...y.
[ACPI Debug] Buffer [0x6]
0: 23 01 00 18 79 00 #...y.
[ACPI Debug] Buffer [0x6]
0: 23 01 00 18 79 00 #...y.
[ACPI Debug] Buffer [0x6]
0: 23 01 00 18 79 00 #...y.
[ACPI Debug] Buffer [0x6]
0: 23 01 00 18 79 00 #...y.
[ACPI Debug] Buffer [0x6]
0: 23 00 02 18 79 00 #...y.
[ACPI Debug] Buffer [0x6]
0: 23 00 02 18 79 00 #...y.
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0x1800-0x1807 mem 0xe8000000-0xe807ffff,0xf0000000-0xf7ffffff irq 16 at device 2.0 on pci0
agp0: <Intel 82865G (865G GMCH) SVGA controller> on vgapci0
agp0: detected 892k stolen memory
agp0: aperture size is 128M
uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0x1820-0x183f irq 16 at device 29.0 on pci0
usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0x1840-0x185f irq 19 at device 29.1 on pci0
usb1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0x1860-0x187f irq 18 at device 29.2 on pci0
usb2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0x1880-0x189f irq 16 at device 29.3 on pci0
usb3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3
uhub3: 2 ports with 2 removable, self powered
ehci0: <Intel 82801EB/R USB 2.0 controller> mem 0xe8080000-0xe80803ff irq 23 at device 29.7 on pci0
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <Intel 82801EB/R USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb4
uhub4: 8 ports with 8 removable, self powered
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci3: <ACPI PCI bus> on pcib1
em0: <Intel(R) PRO/1000 Network Connection 82541EI 7.1.7> port 0x3000-0x303f mem 0xe8100000-0xe811ffff irq 16 at device 11.0 on pci3
em0: MAC address: 00:11:25:06:be:16
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH5 UDMA100 controller> port 0x1810-0x181f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
disk scheduler: set policy of ad0 to fq
ad0: 58644MB <Maxtor 6Y060P0 YAR41BW0> at ata0-master UDMA100
ata1: <ATA channel 1> on atapci0
disk scheduler: set policy of acd0 to noop
acd0: CDRW <HL-DT-ST GCE-8483B/1.02> at ata1-master UDMA33
atapci1: <Intel ICH5 SATA150 controller> port 0x18a0-0x18af,0x1808-0x180b,0x18b0-0x18b7,0x180c-0x180f,0x18b8-0x18bf irq 18 at device 31.2 on pci0
ata2: <ATA channel 0> on atapci1
disk scheduler: set policy of ad4 to fq
ad4: 476940MB <WDC WD5000AAKS-00YGA0 12.01C02> at ata2-master SATA150
ata3: <ATA channel 1> on atapci1
pci0: <serial bus, SMBus> (vendor 0x8086, dev 0x24d3) at device 31.3 irq 17
pcm0: <Intel ICH5 (82801EB)> port 0x1c00-0x1c3f,0x2000-0x20ff mem 0xe8080800-0xe80808ff,0xe8080c00-0xe8080dff irq 17 at device 31.5 on pci0
pcm0: <Analog Devices AD1981B AC97 Codec>
acpi_tz0: <Thermal Zone> on acpi0
acpi_tz0: _CRT value is absurd, ignored (6280.3C)
acpi_button0: <Power Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
fdc0: <NEC 72065B or clone> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
cpu0: <ACPI CPU> on acpi0
cpu_cst0: <ACPI CPU C-State> on cpu0
cpu1: <ACPI CPU> on acpi0
cpu_cst1: <ACPI CPU C-State> on cpu1
orm0: <Option ROMs> at iomem 0xca800-0xcb7ff,0xcb800-0xcc7ff,0xe0000-0xeffff on isa0
pmtimer0 on isa0
fdc1: cannot reserve I/O port range
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio2: can't drain, serial port might not exist, disabling
ppc0: parallel port not found.
CAM: Configuring 4 busses
CAM: finished configuring all busses
disk scheduler: set policy of cd0 to noop
Device Mapper version 4.16.0 loaded
dm_target_zero: Successfully initialized
dm_target_crypt: Successfully initialized
dm_target_error: Successfully initialized
cd0 at ata1 bus 0 target 0 lun 0
cd0: <HL-DT-ST CD-RW GCE-8483B 1.02> Removable CD-ROM SCSI-0 device
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
Mounting root from hammer:serno/Y2P0C2BE.s1d
tryroot serno/Y2P0C2BE.s1d
HAMMER(ROOT) recovery check seqno=48279453
HAMMER(ROOT) recovery range 3000000001def4c0-3000000001def4c0
HAMMER(ROOT) recovery nexto 3000000001def4c0 endseqno=48279454
HAMMER(ROOT) mounted clean, no recovery needed
DMA space used: 332k, remaining available: 16384k
Mounting devfs
Loading configuration files.
Loading devfs rules:
/etc/defaults/devfs.conf
.
Configuring crypto disks.
Enter passphrase for /dev/serno/WD-WCAS80774005.s1d:

disk scheduler: set policy of mapper/temporary-cryptsetup-34 to noop
dm_target_crypt: Setting min/max mpipe buffers: 2/12
kthread 0xcc981260 mpipe_dm_crypt has exited
kthread 0xcc981560 mpipe_dm_crypt has exited
Key slot 0 unlocked.
disk scheduler: set policy of mapper/crypt1 to noop
dm_target_crypt: Setting min/max mpipe buffers: 2/12
dumpon: crash dumps to /dev/serno/Y2P0C2BE.s1b (21, 0x20001)
Starting file system checks:
/dev/serno/Y2P0C2BE.s1a:
FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/serno/Y2P0C2BE.s1a:
clean, 319738 free
(498 frags, 39905 blocks, 0.1% fragmentation)
/dev/serno/WD-WCAS80774005.s1a:
FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/serno/WD-WCAS80774005.s1a:
clean, 319758 free
(206 frags, 39944 blocks, 0.1% fragmentation)
HAMMER(crypt1) recovery check seqno=00ccb366
HAMMER(crypt1) recovery range 300000001dd7bfb8-300000001dd85330
HAMMER(crypt1) recovery nexto 300000001dd85330 endseqno=00ccb3cd
HAMMER(crypt1) recovery undo 300000001dd7bfb8-300000001dd85330 (37752 bytes)(RW)
HAMMER(crypt1) recovery complete
Setting hostname: darner.ixazon.lan.
net.inet6.ip6.accept_rtadv:
0
->
1

lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
options=3<RXCSUM,TXCSUM>
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
em0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=1b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING>
inet 192.168.7.5 netmask 0xffffff00 broadcast 192.168.7.255
inet6 fe80::211:25ff:fe06:be16%em0 prefixlen 64 tentative scopeid 0x1
ether 00:11:25:06:be:16
media: Ethernet autoselect
status: no carrier
add net default: gateway 192.168.7.1
add net 192.168.100.0: gateway 192.168.7.4
Additional routing options:
.
hw.bus.devctl_disable:
0
->
1

Mounting NFS file systems:
.
Building databases...
rcorder:
requirement `mountall' in file `/etc/rc.d/mysqld' has no providers.

rcorder:
requirement `slpd' in file `/etc/rc.d/cupsd' has no providers.

Starting syslogd.
Feb 3 07:49:04 darner syslogd: kernel boot file is /boot/kernel/kernel
No core dumps found.
swapon: adding /dev/serno/Y2P0C2BE.s1b as swap device
swapon: adding /dev/serno/WD-WCAS80774005.s1b as swap device
NFS CLIENT:
access_cache_timeout=5
neg_cache_timeout=3
.
ELF ldconfig path: /usr/lib /usr/lib/gcc41 /usr/lib/gcc44 /usr/lib/compat /usr/pkg/lib /usr/local/lib /etc/ld-elf.so.conf
Starting dntpd.
Starting local daemons:
route:
writing to routing socket
:
File exists
add net 192.168.100.0: gateway chausie: File exists
Using HAMMER PFSs you can define history retention policy per directory tree.
For example, if /home/userA and /home/userB are two PFSs, you can configure that
history is saved 90 days for /home/userA and 30 days for /home/userB. If at
some point many big changes are made, and you would like to recover some of the
space that the history occupies, you can delete history selectively on a per PFS
basis. For example history can be deleted for /home/userA so it only covers 14
days, or granularity can be changed to one week from default of one day. Both
without changing amount of history saved for /home/userB. See "man HAMMER" for
details.
fetchmail: removing stale lockfile
/etc/rc.local: startocat: not found
.
Updating motd.
Starting usbd.
Feb 03 07:49:07.571 [notice] Tor v0.2.2.35 (git-b04388f9e7546a9f). This is experimental software. Do not rely on it for strong anonymity. (Running on DragonFly i386)
Feb 03 07:49:07.687 [notice] Initialized libevent version 2.0.10-stable using method poll. Good.
Feb 03 07:49:07.688 [notice] Opening OR listener on 0.0.0.0:6561
Feb 03 07:49:07.688 [notice] Opening Directory listener on 0.0.0.0:9030
Feb 03 07:49:07.689 [notice] Opening Socks listener on 127.0.0.1:9050
Feb 03 07:49:07.689 [notice] Opening Socks listener on 192.168.7.5:9050
Feb 03 07:49:07.689 [notice] Opening Control listener on 127.0.0.1:9051
Configuring syscons:
keymap
blanktime
.
Starting sshd.
/etc/rc: WARNING: /usr/pkg/etc/socks5.conf is not readable.
Additional ABI support:
.
Starting cron.
Local package initialization:
.
Additional TCP options:
.
Starting privoxy.
postfix/postfix-script: warning: damaged message: corrupt/F2CAB75C500B0
postfix/postfix-script: starting the Postfix mail system
postfix/postfix-script: warning: damaged message: corrupt/F2CAB75C500B0
postfix/postfix-script: starting the Postfix mail system
Feb 3 07:49:12 darner postfix/master[928]: fatal: open lock file pid/master.pid: unable to set exclusive lock: Resource temporarily unavailable
Starting mysqld.
Starting moused:
.
/etc/rc: WARNING: Ignoring scratch file /etc/rc.d/miredo~
Starting inetd.
120203 07:49:12 mysqld_safe Logging to '/var/mysql/darner.ixazon.lan.err'.
Starting dbus.
120203 07:49:13 mysqld_safe Starting mysqld daemon with databases from /var/mysql
Starting cupsd.
Starting apache.
httpd: Could not reliably determine the server's fully qualified domain name, using darner.ixazon.lan for ServerName
[Fri Feb 03 07:49:21 2012] [warn] (2)No such file or directory: Failed to enable the 'httpready' Accept Filter

Fri Feb 3 07:49:22 UTC 2012
drm0: <Intel i865G GMCH> on vgapci0
vgapci0: child drm0 requested pci_enable_busmaster
info: [drm] AGP at 0xf0000000 128MB
info: [drm] Initialized i915 1.6.0 20080730
Feb 3 07:49:31 darner kdm_greet[1071]: Data directory "/var/lib/kdm" not accessible: Permission denied
pmap_collect: collecting pv entries -- suggest increasing PMAP_SHPGPERPROC
pmap_collect: collecting pv entries -- suggest increasing PMAP_SHPGPERPROC
Feb 3 03:00:22 darner su: in pam_sm_authenticate(): (pam_group) neither luser nor ruser specified, assuming ruser
Feb 3 03:00:25 darner su: phma to root on /dev/pts/1
(1-1/4)