Bug #2708


unable to send TCP nor UDP on age(4) interface

Added by dermiste over 9 years ago. Updated almost 3 years ago.

Target version:
Start date:
Due date:
% Done:


Estimated time:


On a fresh install, when using an age(4) interface, I can acquire a DHCP lease, ping my gateway and, but impossible to send TCP nor UDP.

How to reproduce:
1) dhclient age0
2) ping -c 8 # works
3) dig
=> tcpdump on router shows packet going out, but nothing going back in
4) ssh
=> on router, running 'tcpdump -s 1500 -ni eth0 host' shows
19:21:48.844767 IP truncated-ip - 36905 bytes missing! > Flags [S], seq 1807181392:1807218297, win 57344, options [mss 1460,nop,wscale 5,nop,nop,sackOK,nop,nop,TS val 189796 ecr 0], length 36905

  1. uname -a
    DragonFly 3.8-RELEASE DragonFly v3.8.1-RELEASE #16: Mon Jun 16 21:36:15 PDT 2014 :/usr/obj/build/home/justin/src/sys/X86_64_GENERIC x86_64
  1. pciconf -a
    hostb0@pci0:0:0:0: class=0x060000 card=0x81781043 chip=0x27708086 rev=0x81 hdr=0x00
    pcib1@pci0:0:1:0: class=0x060400 card=0x27718086 chip=0x27718086 rev=0x81 hdr=0x01
    pcib2@pci0:0:28:0: class=0x060400 card=0x81791043 chip=0x27d08086 rev=0x01 hdr=0x01
    pcib3@pci0:0:28:2: class=0x060400 card=0x81791043 chip=0x27d48086 rev=0x01 hdr=0x01
    uhci0@pci0:0:29:0: class=0x0c0300 card=0x81791043 chip=0x27c88086 rev=0x01 hdr=0x00
    uhci1@pci0:0:29:1: class=0x0c0300 card=0x81791043 chip=0x27c98086 rev=0x01 hdr=0x00
    uhci2@pci0:0:29:2: class=0x0c0300 card=0x81791043 chip=0x27ca8086 rev=0x01 hdr=0x00
    uhci3@pci0:0:29:3: class=0x0c0300 card=0x81791043 chip=0x27cb8086 rev=0x01 hdr=0x00
    ehci0@pci0:0:29:7: class=0x0c0320 card=0x81791043 chip=0x27cc8086 rev=0x01 hdr=0x00
    pcib4@pci0:0:30:0: class=0x060401 card=0x81791043 chip=0x244e8086 rev=0xe1 hdr=0x01
    isab0@pci0:0:31:0: class=0x060100 card=0x81791043 chip=0x27b88086 rev=0x01 hdr=0x00
    atapci1@pci0:0:31:1: class=0x01018a card=0x81791043 chip=0x27df8086 rev=0x01 hdr=0x00
    atapci2@pci0:0:31:2: class=0x01018f card=0x26011043 chip=0x27c08086 rev=0x01 hdr=0x00
    none0@pci0:0:31:3: class=0x0c0500 card=0x81791043 chip=0x27da8086 rev=0x01 hdr=0x00
    vgapci0@pci0:4:0:0: class=0x030000 card=0x2500174b chip=0x5b601002 rev=0x00 hdr=0x00
    vgapci1@pci0:4:0:1: class=0x038000 card=0x2501174b chip=0x5b701002 rev=0x00 hdr=0x00
    age0@pci0:2:0:0: class=0x020000 card=0x82261043 chip=0x10481969 rev=0xb0 hdr=0x00
    atapci0@pci0:1:9:0: class=0x018000 card=0x31141095 chip=0x31141095 rev=0x02 hdr=0x00
    re0@pci0:1:11:0: class=0x020000 card=0x43001186 chip=0x43001186 rev=0x10 hdr=0x00
  1. dmesg
    Copyright (c) 2003-2014 The DragonFly Project.
    Copyright (c) 1992-2003 The FreeBSD Project.
    Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
    The Regents of the University of California. All rights reserved.
    DragonFly v3.8.1-RELEASE #16: Mon Jun 16 21:36:15 PDT 2014
    TSC clock: 2400065469 Hz, i8254 clock: 1193215 Hz
    CPU: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz (2400.01-MHz K8-class CPU)
    Origin = "GenuineIntel" Id = 0x6f6 Stepping = 6
    AMD Features=0x20000800<SYSCALL,LM>
    AMD Features2=0x1<LAHF>
    Thermal and PM Features=0x1<SENSOR>
    real memory = 1072954368 (1023 MB)
    avail memory = 984633344 (939 MB)
    lapic: divisor index 0, frequency 133333593 Hz
    Initialize MI interrupts
    FQ scheduler policy version 1.1 loaded
    wdog: In-kernel automatic watchdog reset enabled
    kbd1 at kbdmux0
    disk scheduler: set policy of md0 to noop
    md0: Malloc disk
    ACPI: RSDP 0x00000000000FB110 000014 (v00 ACPIAM)
    ACPI: RSDT 0x000000003FFA0000 000040 (v01 A_M_I_ OEMRSDT 06000708 MSFT 00000097)
    ACPI: FACP 0x000000003FFA0200 000081 (v01 A_M_I_ OEMFACP 06000708 MSFT 00000097)
    ACPI: DSDT 0x000000003FFA0590 0059A4 (v01 A0603 A0603000 00000000 INTL 20060113)
    ACPI: FACS 0x000000003FFAE000 000040
    ACPI: APIC 0x000000003FFA0390 000080 (v01 A_M_I_ OEMAPIC 06000708 MSFT 00000097)
    ACPI: OEMB 0x000000003FFAE040 00006B (v01 A_M_I_ AMI_OEM 06000708 MSFT 00000097)
    ACPI: HPET 0x000000003FFA5F40 000038 (v01 A_M_I_ OEMHPET 06000708 MSFT 00000097)
    ACPI: MCFG 0x000000003FFA5F80 00003C (v01 A_M_I_ OEMMCFG 06000708 MSFT 00000097)
    ACPI: SSDT 0x000000003FFAE0B0 0001C6 (v01 AMI CPU1PM 00000001 INTL 20060113)
    ACPI: SSDT 0x000000003FFAE280 00013A (v01 AMI CPU2PM 00000001 INTL 20060113)
    cryptosoft0: <software crypto> on motherboard
    aesni0: No AESNI support.
    padlock0: No ACE support.
    rdrand0: No RdRand support.
    acpi0: <A_M_I_ OEMRSDT> on motherboard
    ACPI: All ACPI Tables successfully acquired
    ACPI FADT: SCI testing interrupt mode ...
    ACPI FADT: SCI select level/high
    ACPI: Executed 1 blocks of module-level executable AML code
    acpi0: Power Button (fixed)
    Warning: ACPI is disabling APM's device. You can't run both
    acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
    acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
    acpi_hpet0: frequency 14318180
    pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
    pci0: <ACPI PCI bus> on pcib0
    pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
    pci4: <ACPI PCI bus> on pcib1
    vgapci0: <VGA-compatible display> port 0xe000-0xe0ff mem 0xe7fe0000-0xe7feffff,0xe8000000-0xefffffff irq 16 at device 0.0 on pci4
    vgapci1: <VGA-compatible display> mem 0xe7ff0000-0xe7ffffff at device 0.1 on pci4
    pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
    pci3: <ACPI PCI bus> on pcib2
    pcib3: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
    pci2: <ACPI PCI bus> on pcib3
    age0: <Attansic Technology Corp, L1 Gigabit Ethernet> mem 0xe7ec0000-0xe7efffff irq 18 at device 0.0 on pci2
    age0: 1280 Tx FIFO, 2364 Rx FIFO
    miibus0: <MII bus> on age0
    atphy0: <Atheros F1 10/100/1000 PHY> on miibus0
    atphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, auto
    age0: MAC address: 00:1b:fc:72:c2:37
    uhci0: <Intel 82801G (ICH7) USB controller USB-A> port 0x7000-0x701f irq 20 at device 29.0 on pci0
    usbus0: <Intel 82801G (ICH7) USB controller USB-A> on uhci0
    uhci1: <Intel 82801G (ICH7) USB controller USB-B> port 0x7400-0x741f irq 17 at device 29.1 on pci0
    usbus0: 12Mbps Full Speed USB v1.0
    ugen0.1: <Intel> at usbus0
    uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
    usbus1: <Intel 82801G (ICH7) USB controller USB-B> on uhci1
    uhci2: <Intel 82801G (ICH7) USB controller USB-C> port 0x7800-0x781f irq 18 at device 29.2 on pci0
    usbus1: 12Mbps Full Speed USB v1.0
    ugen1.1: <Intel> at usbus1
    uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
    usbus2: <Intel 82801G (ICH7) USB controller USB-C> on uhci2
    uhci3: <Intel 82801G (ICH7) USB controller USB-D> port 0x8000-0x801f irq 19 at device 29.3 on pci0
    usbus2: 12Mbps Full Speed USB v1.0
    ugen2.1: <Intel> at usbus2
    uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
    usbus3: <Intel 82801G (ICH7) USB controller USB-D> on uhci3
    ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xe7cffc00-0xe7cfffff irq 20 at device 29.7 on pci0
    usbus4: EHCI version 1.0
    usbus3: 12Mbps Full Speed USB v1.0
    ugen3.1: <Intel> at usbus3
    uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
    usbus4: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0
    pcib4: <ACPI PCI-PCI bridge> at device 30.0 on pci0
    pci1: <ACPI PCI bus> on pcib4
    atapci0: <SiI 3114 SATA150 controller> port 0xa000-0xa00f,0xa400-0xa403,0xa800-0xa807,0xb000-0xb003,0xb400-0xb407 mem 0xe7dff800-0xe7dffbff irq 17 at device 9.0 on pci1
    usbus4: 480Mbps High Speed USB v2.0
    ata2: <ATA channel 0> on atapci0
    ata3: <ATA channel 1> on atapci0
    ata4: <ATA channel 2> on atapci0
    ata5: <ATA channel 3> on atapci0
    re0: <D-Link DGE-528(T) Gigabit Ethernet Adapter> port 0xb800-0xb8ff mem 0xe7dffc00-0xe7dffcff irq 22 at device 11.0 on pci1
    re0: Hardware rev. 0x10000000; PCI32 33MHz
    miibus1: <MII bus> on re0
    rgephy0: <8211B/RTL8169S/8110S media interface> on miibus1
    rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
    uhub0: 2 ports with 2 removable, self powered
    ugen4.1: <Intel> at usbus4
    uhub4: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
    re0: MAC address: 00:19:5b:5d:26:28
    isab0: <PCI-ISA bridge> at device 31.0 on pci0
    isa0: <ISA bus> on isab0
    atapci1: <Intel ICH7 UDMA100 controller> port 0xffa0-0xffaf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.1 on pci0
    ata0: <ATA channel 0> on atapci1
    ata1: <ATA channel 1> on atapci1
    uhub1: 2 ports with 2 removable, self powered
    atapci2: <Intel ICH7 SATA300 controller> port 0x8400-0x840f,0x8800-0x8803,0x9000-0x9007,0x9400-0x9403,0x9800-0x9807 irq 23 at device 31.2 on pci0
    ata6: <ATA channel 0> on atapci2
    uhub2: 2 ports with 2 removable, self powered
    uhub3: 2 ports with 2 removable, self powered
    disk scheduler: set policy of ad12 to noop
    ad12: 76323MB <WDC WD800JD-08MSA1 10.01E01> at ata6-master SATA150
    ata7: <ATA channel 1> on atapci2
    pci0: <serial bus, SMBus> (vendor 0x8086, dev 0x27da) at device 31.3 irq 23
    acpi_button0: <Power Button> on acpi0
    ppc0: <ECP parallel printer port> port 0x778-0x77f,0x378-0x37f irq 7 drq 3 on acpi0
    ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
    ppc0: FIFO with 16/16/9 bytes threshold
    ppbus0: <Parallel port bus> on ppc0
    plip0: <PLIP network interface> on ppbus0
    lpt0: <Printer> on ppbus0
    lpt0: Interrupt-driven port
    ppi0: <Parallel I/O> on ppbus0
    atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
    atkbd0: <AT Keyboard> irq 1 on atkbdc0
    kbd0 at atkbd0
    sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 on acpi0
    sio0: type 16550A
    cpu0: <ACPI CPU> on acpi0
    ACPI: Dynamic OEM Table Load:
    ACPI Error: Method parse/execution failed [\\_PR_.CPU1._OSC] (Node 0xffffffe003347230), AE_ALREADY_EXISTS (20140424/psparse-553)
    cpu_cst0: <ACPI CPU C-State> on cpu0
    cpu_pst0: <ACPI CPU P-State> on cpu0
    clockmod0: <CPU clock modulation> on cpu0
    coretemp0: <CPU On-Die Thermal Sensors> on cpu0
    cpu1: <ACPI CPU> on acpi0
    ACPI: Dynamic OEM Table Load:
    ACPI Error: Method parse/execution failed [\\_PR_.CPU2._OSC] (Node 0xffffffe0033474b8), AE_ALREADY_EXISTS (20140424/psparse-553)
    cpu_cst1: <ACPI CPU C-State> on cpu1
    cpu_pst1: <ACPI CPU P-State> on cpu1
    clockmod1: <CPU clock modulation> on cpu1
    coretemp1: <CPU On-Die Thermal Sensors> on cpu1
    orm0: <Option ROMs> at iomem 0xc0000-0xccfff,0xcd000-0xcdfff on isa0
    pmtimer0 on isa0
    vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
    sc0: <System console> at flags 0x100 on isa0
    sc0: VGA <16 virtual consoles, flags=0x300>
    lm0: <Winbond W83627DHG Hardware Monitor> at port 0x290-0x297 on isa0
    wbsio0: <Winbond LPC Super I/O W83627DHG rev 0x23> at port 0x2e-0x2f on isa0
    wbsio0: hardware monitor iobase is 0x290
    wbsio0: lm0 is already attached at 0x290
    sio2: can't drain, serial port might not exist, disabling
    ppc1: cannot reserve I/O port range
    hpt27xx: no controller detected.
    CAM: Configuring 8 busses
    CAM: finished configuring all busses
    uhub4: 8 ports with 8 removable, self powered
    no B_DEVMAGIC (bootdev=0)
    Device Mapper version 4.16.0 loaded
    dm_target_error: Successfully initialized
    dm_target_zero: Successfully initialized
    Mounting root from ufs:da8s1a
    no disk named 'da8s1a'
    setrootbyname failed
    ffs_mountroot: can't find rootvp
    Root mount failed: 6

Manual root filesystem specification:
<fstype>:<device> Specify root (e.g. ufs:da0s1a)
? List valid disk boot devices
panic Just panic
abort Abort manual input

mountroot> ufs:ad12s2a
Mounting root from ufs:ad12s2a
DMA space used: 588k, remaining available: 16384k
Mounting devfs

Actions #1

Updated by tuxillo almost 3 years ago

  • Target version changed from 3.8 to 6.0

Also available in: Atom PDF