DragonFlyBSD

On Mon, Aug 24, 2009 at 1:40 PM, <elekktretterr@exemail.com.au> wrote:

Hi,

Ive been trying to install the latest snapshot (22nd august) to a new HP
Proliant DL180 G5.
2)
when I go to setup networking in the "configuration" stage after the data
has been cpduped to the disk, i choose DHCP and the system panics upon
running dhclient bge0.

panic: bogus ife->ifm_data(10)

mii_phy_set_media(d02abd30) at mii_phy_set_media+0x8a
ukphy_service(d02abd30,c28c2b80,2) at ukphy_service+0xec

Could you post the bootverbose dmesg? bge(4) normally should have
brgphy attached.

Best Regards,
sephe

Could you post the bootverbose dmesg? bge(4) normally should have
brgphy attached.

Best Regards,
sephe

Which part are you looking for? Im gonna have to type it up.

Petr

Managed to get the full verbose dmesg. Its attached to this email.

Moin,

• elekktretterr@exemail.com.au wrote:

Hi,

Ive been trying to install the latest snapshot (22nd august) to a new HP
Proliant DL180 G5.

So far 4 issues:

1)
Installer spews upon trying to execute /bin/dd if=/dev/zero of=/dev/da0s1
bs=32k count=16.

dd: /dev/da0s1: Read-Only Filesystem

But you seem to be able to choose "Skip" and it progresses further into
the install to setup partitions.

I can confirm that. I just thought it was an issue on my side, pressed
"Skip" and forgot about the issue :) I can provide more information if
that's needed.

Cheers

Matthias

I can confirm that. I just thought it was an issue on my side, pressed
"Skip" and forgot about the issue :) I can provide more information if
that's needed.

Cheers

I was wondering if this could have anything to do with not being able to
find HAMMER root partition. I skipped the error, finished the install and
rebooted and then mountroot complained that da0s1 cannot be found. However
because any keyboard refuses to work in mountroot and gdb shells I couldnt
really try anything else.

Petr

I was wondering if this could have anything to do with not being able to
find HAMMER root partition. I skipped the error, finished the install and
rebooted and then mountroot complained that da0s1 cannot be found. However
because any keyboard refuses to work in mountroot and gdb shells I couldnt
really try anything else.

Further update on this issue. It seems that for some strange reason, every
now and then mounting of the root file system during boot happens before
the initialization of cd0 (in case of livecd) or da0 (in case of DragonFly
already being installed on disk). This seems to happen randomly for
booting of the livecd, but happens constantly when booting of the hard
disk. After that, I cannot use a keyboard -> it seems that the system is
"stuck" and has to be reset.

Petr

Further update on this issue. It seems that for some strange reason, every
now and then mounting of the root file system during boot happens before
the initialization of cd0 (in case of livecd) or da0 (in case of DragonFly
already being installed on disk). This seems to happen randomly for
booting of the livecd, but happens constantly when booting of the hard
disk. After that, I cannot use a keyboard -> it seems that the system is
"stuck" and has to be reset.

Does anyone have a clue as to why this would be happening?

Hi,

• elekktretterr@exemail.com.au wrote:

Hi,

Ive been trying to install the latest snapshot (22nd august) to a new HP
Proliant DL180 G5.

So far 4 issues:

1)
Installer spews upon trying to execute /bin/dd if=/dev/zero of=/dev/da0s1
bs=32k count=16.

dd: /dev/da0s1: Read-Only Filesystem

But you seem to be able to choose "Skip" and it progresses further into
the install to setup partitions.

I stumbled across this because I created the label with Linux fdisk
(which was installed before installing DragonFly). Do you installed
DragonFly on the whole disk or do you used a pre-partitioned HDD?

Cheers

Matthias

I stumbled across this because I created the label with Linux fdisk
(which was installed before installing DragonFly). Do you installed
DragonFly on the whole disk or do you used a pre-partitioned HDD?

Hi Mathias,

On the whole disk. As far as I know they have never been partitioned before.

Petr

Hmm, the "Read-only file system" message upon dd seems to be something new.

Last time I tried an ISO (August 15), this problem didn't occur. A current one
shows it here, too.

elekktretterr@exemail.com.au schrieb:

Hi,

Ive been trying to install the latest snapshot (22nd august) to a new HP
Proliant DL180 G5.

So far 4 issues:

In general, it's not a good idea to put several issues into one report,
as it becomes increasingly difficult to see who is responding to which
of the sub-issues in our bug tracker.

Sascha

Closing this issue.

(1) is fixed by a2f6293fd245bd17fea42cddc69bc93d3c1def32, (2) by
a1678a342c788b812f22fbe83af6e76f7c586884, and two separate issues (1463 & 1464)
have been opened for (3) and (4).