DragonFlyBSD

Also "shutdown -h now" does not succeed because of:

Shutting down ACPI
AcpiOsReleaseObject: Double Free 0xc6cef354

(using latest snapshot of 2.4 from chlamydia)

Tomaž

Have you tried booting with ACPI disabled?

2009/10/19 Tomaž Borštnar <tomaz.borstnar@over.net>:

Hello!

I have a HP DL360G4p machine with 5 gigs of RAM, internal SATA disk
and HP SmartArray 6400 controller (2 channels) with 6400EM card (additional
2 channels attached as daughter card) with MSA20 enclosure with SATA disks -
configured as 4 volumes. Install went fine, but dmesg prints some errors
(full dmesg output attached), but here are relevant parts:

bge0: <Broadcom BCM5704C Dual Gigabit Ethernet> mem 0xfddf0000-0xfddfffff
irq 7 at device 2.0 on pci2
bge0: CHIP ID 0x21000000; ASIC REV 0x02; CHIP REV 0x21; PCI-X
alignment check failed
miibus0: <MII bus> on bge0
brgphy0: <BCM5704 10/100/1000baseT PHY> on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
bge0: MAC address: 00:15:60:0f:b0:e8
bge1: <Broadcom BCM5704C Dual Gigabit Ethernet> mem 0xfdde0000-0xfddeffff
irq 7 at device 2.1 on pci2
bge1: CHIP ID 0x21000000; ASIC REV 0x02; CHIP REV 0x21; PCI-X
alignment check failed
alignment check failed
miibus1: <MII bus> on bge1
brgphy1: <BCM5704 10/100/1000baseT PHY> on miibus1
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
bge1: MAC address: 00:15:60:0f:b0:e7

I think you mean the "alignment check failed", it is quite common and
you can jut ignore them

Best Regards,
sephe

2009/10/19 Tomaž Borštnar <tomaz.borstnar@over.net>:

Also "shutdown -h now" does not succeed because of:

Have you tried "shutdown -p now"? I think Linux powers off the
machine if "shutdown -h now" is used.

Shutting down ACPI
AcpiOsReleaseObject: Double Free 0xc6cef354

I was trying to track it down several days ago, but didn't find the root cause.
It is related to the acpi cpu module but not acpi cpu_cst and acpi
cpu_pst module.

Best Regards,
sephe

Sepherosa Ziehau wrote:

2009/10/19 Tomaž Borštnar <tomaz.borstnar@over.net>:

Hello!

I have a HP DL360G4p machine with 5 gigs of RAM, internal SATA disk
and HP SmartArray 6400 controller (2 channels) with 6400EM card (additional
2 channels attached as daughter card) with MSA20 enclosure with SATA disks -
configured as 4 volumes. Install went fine, but dmesg prints some errors
(full dmesg output attached), but here are relevant parts:

bge0: <Broadcom BCM5704C Dual Gigabit Ethernet> mem 0xfddf0000-0xfddfffff
irq 7 at device 2.0 on pci2
bge0: CHIP ID 0x21000000; ASIC REV 0x02; CHIP REV 0x21; PCI-X
alignment check failed
miibus0: <MII bus> on bge0
brgphy0: <BCM5704 10/100/1000baseT PHY> on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
bge0: MAC address: 00:15:60:0f:b0:e8
bge1: <Broadcom BCM5704C Dual Gigabit Ethernet> mem 0xfdde0000-0xfddeffff
irq 7 at device 2.1 on pci2
bge1: CHIP ID 0x21000000; ASIC REV 0x02; CHIP REV 0x21; PCI-X
alignment check failed
alignment check failed
miibus1: <MII bus> on bge1
brgphy1: <BCM5704 10/100/1000baseT PHY> on miibus1
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
bge1: MAC address: 00:15:60:0f:b0:e7

I think you mean the "alignment check failed", it is quite common and
you can jut ignore them

Maybe we should remove the message then? :)

cheers
simon

Hi,

CAM: Configuring 5 busses
CAM: finished configuring all busses (-2 left)

-2 busses?

xpt_finishconfig_task() seems to do nothing if busses_to_config != 0
Is this intended?

Btw, busses_to_config counter is only decreased in xptconfigfunc() and
xpt_finishconfig().

Cheers,
Antonio Huete